ECU module programming guide using FDRS

[Way2qk4u2c]

Is this normal or am I missing a step?

I went down the FDRS rabbit hole for bluecruise v1.4. I have run the PSCM and ACM 3x and it still pops up. Do i keep hitting run until it stops doing that or is there a underlying error that i can't see preventing it from fully completing? From the beginning i didnt have any GWM or APIM updates just IPMA,PSCM, and TCM.

Sponsored

 

[Way2qk4u2c]

While searching here i think i found my answer
Do the BCMC. I would also try the DSP again, but if it continues to linger, ignore it. The ACM and recently the PSCM have been reported to not come off the list after you update it.

Sync 24127 is the latest available for our trucks, so you're good to go there.

 

[Way2qk4u2c]

Should i be worried about this? IPMA and PSCM?

Im guessing the IPMA dtc is for the 360 camera recalibration is needed...

When i rescanned the PSCM came back as passed.

 

[rugedraw]

Is this normal or am I missing a step?

I went down the FDRS rabbit hole for bluecruise v1.4. I have run the PSCM and ACM 3x and it still pops up. Do i keep hitting run until it stops doing that or is there a underlying error that i can't see preventing it from fully completing? From the beginning i didnt have any GWM or APIM updates just IPMA,PSCM, and TCM.

ACM is known not to come off the list and the BCM you cannot do.

For the PSCM, @Mike G discovered a way to get it to clear. Go to the toolbox, click the IPMA and run the IPMA configuration routine on it. If that fails, then PMI the IPMA and when FDRS asks if it is the original module, click no. Details are here:

https://www.f150lightningforum.com/...programming-guide-using-fdrs.8249/post-453028

 

[Way2qk4u2c]

Well I got everything updated and did the FORscan changes but now blue cruise won’t even activate on the highway. I get a warning on the dash that lane centering assist is not available. Does anyone have ideas that could cause this?

 

[rugedraw]

Well I got everything updated and did the FORscan changes but now blue cruise won’t even activate on the highway. I get a warning on the dash that lane centering assist is not available. Does anyone have ideas that could cause this?

@m_bt54 Is this the same issue you had?

 

[m_bt54]

@m_bt54 Is this the same issue you had?

Exactly the same issue unfortunately. Let me know if I can help in any way

 

[Way2qk4u2c]

Exactly the same issue unfortunately. Let me know if I can help in any way

No one has found a solution yet?

Is it possibly another for scan setting that we all have.

 

[m_bt54]

No one has found a solution yet?

Is it possibly another for scan setting that we all have.

We tried but ended up having to roll back the update after all attempts.

 

[Way2qk4u2c]

We tried but ended up having to roll back the update after all attempts.

Bummer! Well I’m one of the lucky ones

 

[m_bt54]

Bummer! Well I’m one of the lucky ones

How are you lucky? Did you figure out the issue ?

 

[Way2qk4u2c]

How are you lucky? Did you figure out the issue ?

I’m lucky to be in the same situation you are.

 

[m_bt54]

I’m lucky to be in the same situation you are.

Ah ok. Being a little over optimistic with my assumption

 

[PlatPwrboost]

Are your trucks 2021 job #1 or Job #2? My truck is a job 2 and had no issues, maybe is the trucks that didn’t come with BC enabled and later got enabled? Any thoughts on this?

 

[Way2qk4u2c]

Mine is a 2022 job #2 BC enabled

The unusual thing is when I hit cruise it locks in the speed without the need to hit the set button. Almost like it’s configured wrong. It will also slow me down in curves and have an arrow so it’s like enabled but yet not. Very strange behavior.

Sponsored