ECU module programming guide using FDRS

[Jesse-Infotainment]

Thanks for checking history. I mistakenly assumed DTC's persist for some time unless cleared, but if they come and go in shorter periods makes sense why I've never noticed it on the other handful of times I was in looking at something prior to dealer visit. Outside the expected HVAC popping right back, this is the first one to come right back after refreshing post clear.

Sounds like I have a new feature

Yeah this one comes and goes. I dont think I have seen a truck that doesnt have it

I have given up being worried about some DTCs. I get Lane assist DTCs I though must be my truck then I looked and every one has them.

These trucks just seem to get them for whatever reason.

Sponsored

 

[wvfan44]

When someone get some time could you please look up my Vin: 1FTFW1ED0MFB41051

Looking to see how many update that i have?

Question: I haven't done FDRS updates in a bit.. With double honk and window down with key fob enabled should I change them back before doing any module updates?

Appreciate everyone!

 

[Cheez_Greater]

Hi, Jesse has been helping me trying to get past the 1.7.1 stuck update. I've had it run and go through update and then I get USB Error 0. Jesse nor I have any idea what Error 0 is. Anyone else run into this? Been trying to go through this thread but taking forever with 400+ pages, lol.

I am having the same USB Error 0 issue with 3 different sticks, USB A and C, all formatted exFAT and the default allocation size. I've tried and retried probably 2 dozen times and no luck yet. The update process also starts after only a few minutes which seems way faster than it does for those who have successful updates.

 

[Bdubbs1198]

I am having the same USB Error 0 issue with 3 different sticks, USB A and C, all formatted exFAT and the default allocation size. I've tried and retried probably 2 dozen times and no luck yet. The update process also starts after only a few minutes which seems way faster than it does for those who have successful updates.

So frustrating

 

[davidb525]

@Jesse-Infotainment

Do you recommend this change to the State of Charge (SOC) for our batteries from 80% to 95%?

Battery State of Charge Rate (SOC) 726-08-02 xxxx - xx05 - F0xx xx05 - F0xx=95% | xx05 - 00xx=80%(stock)

Here are a few other Target State of Charge settings you can try if you don't want to take it to 95%

xxxx xx05 00-- = 80%

xxxx xxx05 50-- = 85%

xxxx xx05 A0-- = 90%

xxxx xx05 F0-- = 95%

xxxx xx06 20-- = 98%

xxxx xx06 40-- = 100%

 

[MikeYQM]

Can anyone run my vin for updates please & thank you?

1FTFW1ED2MFB10996

 

[Shoebox72069]

Well I can't believe it.

I was thinking about getting a license to update my BECM that is FINALLY showing up in my as-built data after like... 7 months of being absent.

I only took the truck yesterday for a couple mile drive to drop off some leaves and yesterday evening, 3.5.2 rolled in.

I think I might still buy a license to top off the BECM among other things regardless, but at least happy to see that OTA is for the moment... functional, until Ford decides to brick it again.

 

[rugedraw]

When someone get some time could you please look up my Vin: 1FTFW1ED0MFB41051

Looking to see how many update that i have?

Question: I haven't done FDRS updates in a bit.. With double honk and window down with key fob enabled should I change them back before doing any module updates?


Appreciate everyone!

We can only see the past 60 days of OTA history, and you got the two small patches before 3.5.2 and you got 3.5.2 just ten days ago. Your OTA's seem to be flowing nicely.

Can anyone run my vin for updates please & thank you?

1FTFW1ED2MFB10996

Same exact response as above applies to you. You also got 3.5.2 ten days ago.

 

[ENG430]

When someone get some time could you please look up my Vin: 1FTFW1ED0MFB41051

Looking to see how many update that i have?

Question: I haven't done FDRS updates in a bit.. With double honk and window down with key fob enabled should I change them back before doing any module updates?

Appreciate everyone!

APIM
WACM
BCM

 

[ENG430]

Can anyone run my vin for updates please & thank you?

1FTFW1ED2MFB10996

APIM
BCM

 

[jflottawa]

I *just* picked up my truck on Friday, but was curious as to how far off it might be in terms of updates.

I fully intend on ordering the hardware to do this myself in the future, but if someone could give me this one-time lookup I'd greatly appreciate it!

1FTFW1ED7NFB56079

Thanks!

 

[speedracercjr]

I *just* picked up my truck on Friday, but was curious as to how far off it might be in terms of updates.

I fully intend on ordering the hardware to do this myself in the future, but if someone could give me this one-time lookup I'd greatly appreciate it!

1FTFW1ED7NFB56079

Thanks!

Just a couple:

 

[jflottawa]

Just a couple:

Thanks very much!!

 

[CoCamper]

Many thanks to all who have contributed here. Just got FDRS working and did 4 hrs of updates yesterday. All went smoothly, pretty stoked on how it went.

This forum and thread are amazing.

 

[MikeYQM]

I was doing a BCM update today and got this message with no DTC or noticeable drivability issues. Any ideas?

Sponsored