ECU module programming guide using FDRS

[jfalat]

Try this

Thanks, HammaMan... that fix it... much appreciated...

Sponsored

 

[ReverendQ]

Thanks, HammaMan... that fix it... much appreciated...

@HammaMan, admit him to the HMWH club.

 

[rugedraw]

Have to run TRON authentication

TRON started with the 2024 models, correct?

 

[Ajzride]

TRON started with the 2024 models, correct?

Yes

 

[farmtruckman]

Let me ask then. So what exactly is TRON please?

 

[Ajzride]

Let me ask then. So what exactly is TRON please?

it’s encryption of the canbus network.

 

[JohnTrigger]

Did a few updates to night. DDM PDM ACM GWM AND TCU... All updates went good.. but i went to look at DTC and i have this showing. anyone know why this saying not programed.

I had the same above error, back in Oct ‘24 on this post in this thread:
https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-528314

Googled the SSM52730 referenced in bottom right corner back then and answered my own post on the very next post:

SSM 52730 - 2023-2024 F-Super Duty And 2024 F-150/Nautilus - Diagnostic Trouble Code (DTC) U211B:51 Stored In The TCU After Software Update Or An OTA

Some 2023-2024 F-Super Duty and 2024 F-150/Nautilus vehicles may set DTC U211B:51 in the telematics control unit (TCU) module after a software update on the TCU is performed at dealer or via over the air (OTA) Update. The DTC U211B:51 in the TCU has no effect on vehicle functionality or connectivity. Replacement or reprogramming of the TCU will not resolve this condition. DTC U211B:51 should be ignored if no other DTCs are present in the TCU and no symptoms present. No further service action is required.

Now I know I need to run TRON next time I’m in FDRS. Thanks!

Have to run TRON authentication

 

[jfalat]

I had the same above error, back in Oct ‘24 on this post in this thread:
https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-528314

Googled the SSM52730 referenced in bottom right corner back then and answered my own post on the very next post:

SSM 52730 - 2023-2024 F-Super Duty And 2024 F-150/Nautilus - Diagnostic Trouble Code (DTC) U211B:51 Stored In The TCU After Software Update Or An OTA

Some 2023-2024 F-Super Duty and 2024 F-150/Nautilus vehicles may set DTC U211B:51 in the telematics control unit (TCU) module after a software update on the TCU is performed at dealer or via over the air (OTA) Update. The DTC U211B:51 in the TCU has no effect on vehicle functionality or connectivity. Replacement or reprogramming of the TCU will not resolve this condition. DTC U211B:51 should be ignored if no other DTCs are present in the TCU and no symptoms present. No further service action is required.

Now I know I need to run TRON next time I’m in FDRS. Thanks!

Thankyou…I did not notice the TSB. I guess I was mad at a update to fix your truck would cause a issue..

 

[jfalat]

I will add this. i ran the test 2 times they both failed but it did clear the code after i did a retest on modules.

 

[SpaceEngineer]

I am attempting to use FDRS for the first time and cannot seem to log in. I am assuming it is tied to this: when I log into the motorcraft services website, the updated T&C are not loading in for me to accept. I am using an edge browser with popups disabled. I tried creating a new account and different computers, but am having the same results.
If anyone has tips or tricks to get past this, it would be greatly appreciated.

 

[JEB]

I am attempting to use FDRS for the first time and cannot seem to log in. I am assuming it is tied to this: when I log into the motorcraft services website, the updated T&C are not loading in for me to accept. I am using an edge browser with popups disabled. I tried creating a new account and different computers, but am having the same results.
If anyone has tips or tricks to get past this, it would be greatly appreciated.

The motorcraftservice.com page has been a little wonky recently. See if you have any better luck logging into fordserviceinfo.com.

 

[SpaceEngineer]

The motorcraftservice.com page has been a little wonky recently. See if you have any better luck logging into fordserviceinfo.com.

That worked. Thanks for your help.

 

[arob1011]

Been working on updates most of the day. Got to the IPC and got the usb error 0. Does anyone know the resolution to this?

 

[HammaMan]

Did a few updates to night. DDM PDM ACM GWM AND TCU... All updates went good.. but i went to look at DTC and i have this showing. anyone know why this saying not programed.

Just fixed another truck w/ this issue today. Seems the TCU update breaks its TRON encryption for some reason.

 

[Ajzride]

Been working on updates most of the day. Got to the IPC and got the usb error 0. Does anyone know the resolution to this?

reformat the stick and try again. Is it a known working USB (ie it worked for other updates already today)?

Sponsored