Need Help bad!!!..2021+ F150 people

[22Platinum]

Id help you but there's a heat wave for the next few days in Virginia.

Real hopeful you create a thread for that livernois engine build, im completely stoked to hear numbers!

Sponsored

 

[SALEEN961]

Some of these measurements are going to vary with brake wear and with our calipers the exact location for measurements B and C are debatable. My toddler decided to "help" me so please verify my measurements just in case I dropped the ball here. Everyone in my house is severely sleep deprived so I'm not sure if anyone here can be trusted to read a tape measure right now.

This is with new Ford pads, EBC rotors, and the brakes pumped up to take up the free play in our floating calipers.

Front:
A: 106.7 mm
B: 157.7 mm
C: 173.6 mm
D: 196.0 mm
E: 21.2 mm
F 9.8 mm

 

[Riddick]

You try calling Midnight Performance in Houston? They have the fastest F-150s around and have literally built hundreds of them.

 

[SilverPigeon]

Thanks man, appreciate it..
If you could get just the front, because you don't have the Max Tow rear axle, that would help greatly..

I do, at least that's what I ordered, I'll find out when I take a rear wheel off.

...the larger calipers yet...

FYI, the caliper is the same, it's the rotor that's larger (336/20 vs. 350/24) which increases swept area. Of course, this may very well change the measurements between non- and Max-Tow, which is why I'll look at the rear as well.

 

[Tank]

I do, at least that's what I ordered, I'll find out when I take a rear wheel off.
FYI, the caliper is the same, it's the rotor that's larger (336/20 vs. 350/24) which increases swept area. Of course, this may very well change the measurements between non- and Max-Tow, which is why I'll look at the rear as well.

Thank you...I know all the particulars, and am very well versed in the Powerboost...I have actually held the World Record for fastest and highest hp Powerboost for over a year...still do...
...what I don't know is the measurements that I need.
..Any help with those measurements would be greatly appreciated..

 

[Tank]

Id help you but there's a heat wave for the next few days in Virginia.

Real hopeful you create a thread for that livernois engine build, im completely stoked to hear numbers!

I appreciate it, but if my truck was here, I'd be measuring in the heatwave of south Louisiana....its a touch hotter here...?

 

[bjl95mustang]

Why not just have the shop who has your truck do this for you? I bet they are more than capable to get it done. And it will probably be your best route for accurate measurements.

Not bashing anyone, but people make mistakes and your basing your order on something from someone off the internet.

 

[Tank]

You try calling Midnight Performance in Houston? They have the fastest F-150s around and have literally built hundreds of them.

And not one of them is a Max Tow axle, they are all the little 8.8 axles.. thanks though.

 

[Tank]

Id help you but there's a heat wave for the next few days in Virginia.

Real hopeful you create a thread for that livernois engine build, im completely stoked to hear numbers!

I rarely post here....I always post on my Facebook group... "F150 Powerboost Owners 21+"..

I have over 33,000 Powerboost members there.

But, I will try to remember to post here too!

 

[SilverPigeon]

Thank you...I know all the particulars, and am very well versed in the Powerboost...I have actually held the World Record for fastest and highest hp Powerboost for over a year...still do...
...what I don't know is the measurements that I need.
..Any help with those measurements would be greatly appreciated..

Simply corrected an error of yours. I could not care less about your records. I already said I would help you with the measurements Tuesday my time.

You won't answer questions of why a shop where the truck is cannot do them. Jay, you need to rethink your attitude towards people who are willing to help you.

 

[Tank]

Simply corrected an error of yours. I could not care less about your records. I already said I would help you with the measurements Tuesday my time.

You won't answer questions of why a shop where the truck is cannot do them. Jay, you need to rethink your attitude towards people who are willing to help you.

My apologies...retired military with a short fuse.
..I had this posted on 9 places, for over a week...and everyone wants to ask questions, and it just gets annoying answering hundreds of questions, yet get zero help...so I'm ignoring everything that doesn't pertain to the specific reason of the post(getting measurements).

It's like posting something on Marketplace, and getting "is this still available?" 4,000 times....when all you want to say is "if you can't help me, then please just shut the fuck up and go away".....
...so...you can see my frustration....again, my apologies.

Obviously I asked, Obviously there is a reason why they can't at this time..

I appreciate the help..

 

[NVRANUF]

 

[NVRANUF]

OP be like..........

 

[Riddick]

You guys are cracking me up, where did the pic go talking about the world record? 11.6 second truck and talking about a world record, must be a micro record of some sort.

OP, best of luck on your goals with the new set up. Also, thanks for your service... retired aircraft maintainer here.

 

[Tank]

Pure gold sir!...??
Im stealing it and posting it on all the places I posted asking for help....
...and after all this...I still need the measurements...?

Sponsored