2021+ F-150 FORScan List / Database / Spreadsheet

[digitaltrucker]

Anyone figured out how to disable AS/S yet with the 2024/2025 trucks?

https://www.amazon.com/Tech-Auto-Start-Stop-Eliminator/dp/B0BHXHWM2F

Sponsored

 

[FirstFord]

So without an aux cam mounted on a trailer etc. or without a trailer connected and set up, the only other normal view is the 50-50 view. As standard you have front, front 180°, 360°, bed, hitch, reverse, reverse 180°.

50-50 is the Split View down each side of the truck. The soft menu button is a truck with 2 down arrows on it. If you don't have that, you can do:
Enable 50-50 viewsAPIM7D0-01-01was: xxxx 0xxx xx--new: xxxx 2xxx xx-- If your "was" is different, let me know.

If you want all the views at speed, also do these (again, if "was" is different, let me know):
FeatureModule:Address :Was:New:Enable Cameras at SpeedAPIM7D0-01-01xxxx xxxx BC--xxxx xxxx FD--Enable Off Road Views at SpeedAPIM7D0-01-04xxxx DCxx xx--xxxx FDxx xx--Enable 50-50 views at speedAPIM7D0-01-04xxxx xxxx x0--xxxx xxxx x1--Enable 50-50 views at speedIPMA706-01-020xxx xxxx xx--3xxx xxxx xx--Enable Cameras at SpeedIPMA706-02-02xxxD CExx xx--xxxF CExx xx--Enable OffRoad (Rock Crawl, Mud/Ruts,
and Deep Snow/Sand) Front Camera at SpeedIPMA706-02-02xxxx xx00 xx--xxxx xx03 xx-- The last one also gives you tyre tracks on the view which move with the steering wheel. Reboot both the APIM and IPMA in service procedures if needed.

VERY nice write-up, by the way.... I read with interest, as I think I'm finally ready to make these mods. With absolutely NO disrespect intended to Livingitup, I appreciated the additional explanations you gave for each address - helpful.

As a part of taking a closer look at this, I compared the values posted on Livingitup's spreadsheet under the "Common" tab, as well as under his APIM tab, and also compared to the values you posted. The comparison triggered some questions:

1) For Enable Cameras At Speed:
On the "Common" tab Livingitup posted APIM 7D0-01-01 xxxx xxxx FD-- (as did you). If you look at the APIM tab, the "D" translates to:

DAFVCSV Available • MCS Soft Button Camera Toggle • TRG Disabled • CHMSLC Enabled

Specific to TRG (Trailer Reverse Guidance), why would you want that feature disabled? (I'm not challenging you, I'm asking out of ignorance.) Choosing "E" for the value instead of "D" leaves the TRG enabled. Does this pose some problem that I'm not aware of?

2) Both you and Livingitup list APIM 7D0-01-04 xxxx FDxx xx--, except Livingitup has it listed on the Common Tab, under "Enable Cameras At Speed" and you have it listed under "Enable Off Road Views at Speed". Is there something that I am overlooking here, is there a difference? Much more to the point, for the same address Livingitup posts a note that says, "use FF if you have 1-pedal drive". What the heck does that mean? What's 1-pedal drive?

 

[SilverPigeon]

....why would you want that feature disabled? (I'm not challenging you, I'm asking out of ignorance.) Choosing "E" for the value instead of "D" leaves the TRG enabled. Does this pose some problem that I'm not aware of?

The only explanation I have for that is that even though I have pro trailer backup assist, TRG must not be a part of that. However, if you had TRG enabled originally, you'd leave it enabled, which would make that new value "F" instead of a "D". Also note that the values being seen in the sheet are not all for the F-150, e.g. there are values for many models in "Vehicle Type" settings in some modules. It's possible that if we all have TRG disabled, it may not be a setting for us.

...is there a difference? Much more to the point, for the same address Livingitup posts a note that says, "use FF if you have 1-pedal drive". ...What's 1-pedal drive?

No, there is no difference, I just made my own sheet for my own clarity. That value enables both rear camera at speed and off road views at speed. Also hitch view and 1-pedal drive, which, I presume, is for handicapped people where they lift off the accelerator and it brakes for them ?‍

 

[rugedraw]

The only explanation I have for that is that even though I have pro trailer backup assist, TRG must not be a part of that. However, if you had TRG enabled originally, you'd leave it enabled, which would make that new value "F" instead of a "D". Also note that the values being seen in the sheet are not all for the F-150, e.g. there are values for many models in "Vehicle Type" settings in some modules. It's possible that if we all have TRG disabled, it may not be a setting for us.
No, there is no difference, I just made my own sheet for my own clarity. That value enables both rear camera at speed and off road views at speed. Also hitch view and 1-pedal drive, which, I presume, is for handicapped people where they lift off the accelerator and it brakes for them ?‍

1PD is for the EV's only, but that is exactly what it does.

 

[yatsek]

I just want to say this forum is full of very useful info. I'm grateful to all of the guys (and gals) who help out.

I was getting ready to start making some mods with Forscan so last week I backed up all of my as-built modules. This morning before making a change I backed up my as-built IPMA . Then out of curiosity I compared the last week IPMA file with today's using

http://compulsivecode.com/Project_AsBuiltCompare.aspx

There were some differences in the 706-29-xx range.


Is this normal for the IPMA module data to differ so much based on different dates? I made no modifications in between.


I compared some of the 706-29-xx values with my VIN as-built info and they were different too. All 3 files.

https://www.motorcraftservice.com/AsBuilt

Based on Livinitup's spreadsheet "IPMA 2003 706" tab, the 706-29-xxxx range is SensorCfg_DPAC_Homography2 (SCDPACH)

Is this some kind of dynamic sensor data or unused ?

Thanks

 

[FirstFord]

Also note that the values being seen in the sheet are not all for the F-150, e.g. there are values for many models in "Vehicle Type" settings in some modules.

Great point, and something that I had not considered. After digging into this deeper and looking at the Ford provided values on my own truck, I came to realize that there are at least two listed value changes that I don't have to change at all - they are already the correct values.

Again, great write up. You are providing a valuable service

 

[FirstFord]

1PD is for the EV's only, but that is exactly what it does.

Ah hah! Well, that does explain things! Thanks!

 

[NYC_Raptor_R]

Just a heads up if anyone is interested, This works for a 2024 Raptor R . Not sure on the v6 Raptors or on other models but if you wanted coolant , engine oil and transmission temps in digital numerical format under the dials up at the top , i used the following coding and it works. I was aware of the coolant and trans working but just found out this works for engine oil temp as well.

IPC 720-07-01 / xxxx-xx54-xx--

 

[DeltaDeuce]

Just traded a 21 Platinum that I enabled Glare Free lighting on and would like to add it to my 2025 F150 Platinum High version. Has anybody cracked the code yet? See what we have only works for 21-22 model years.

 

[svtzx2]

I have a 24 Lariat and I can’t get it to work. (Wrong type lights from the factory) Platinum in Canada comes with it enabled from the factory.

 

[mau47]

Just traded a 21 Platinum that I enabled Glare Free lighting on and would like to add it to my 2025 F150 Platinum High version. Has anybody cracked the code yet? See what we have only works for 21-22 model years.

I saw a post saying the new trucks don't have the appropriate hardware for it anymore so it won't be possible. Not sure if that is 100% confirmed or not.

 

[BMagFX4]

Ok I’m kinda dumb. But I added the factory trailer brake controller and programmed everything on forscan but TRM says 791-01-02 the second letter of the second block needs to add 1 to whatever is there. Mine says FF98. What is F+1??

 

[SilverPigeon]

Ok I’m kinda dumb. But I added the factory trailer brake controller and programmed everything on forscan but TRM says 791-01-02 the second letter of the second block needs to add 1 to whatever is there. Mine says FF98. What is F+1??

Because these are effectively enable/disable switches, if you already have F, then they are all enabled, which I presume is the intent of TBMC, therefore no need to further modify that value.

 

[rugedraw]

Hey guys.....trying to help a member out with a little project. Need the ab data off the GWM for a Tremor with these (or close to these) specs. Can anyone grab me the .abt file?

 

[Paul Neubauer]

Hey guys.....trying to help a member out with a little project. Need the ab data off the GWM for a Tremor with these (or close to these) specs. Can anyone grab me the .abt file?

https://www.autotrader.com/cars-for...F150PICKUP|Tremor&zip=77001&clickType=listing

Sponsored