ECU module programming guide using FDRS

[malfaour]

I always have KPH and miles on my speedometer after updates. ?

Okay digging up an old thread since you have an XLT. Here is a thread by someone who also had an XLT and they could never get it to stop resetting. ?

https://www.f150gen14.com/forum/threads/canadian-truck-in-the-us.13720/

Like I said, I just was trying to see if possible. If not, its not a big.

Sponsored

 

[SilverPigeon]

Bingo! @malfaour Moe, change Display Unit Selection Function to imperial. That will default the speedo to mph.

 

[Paul Neubauer]

I am now way too invested in seeing the outcome of this Canadian truck!

 

[malfaour]

Bingo! @malfaour Moe, change Display Unit Selection Function to imperial. That will default the speedo to mph.

K. So I did that, and guess what, every is canadian lol

 

[malfaour]

Bingo! @malfaour Moe, change Display Unit Selection Function to imperial. That will default the speedo to mph.

It shows mph as default I guess now. Everything else is Canadian. So progress?

 

[SilverPigeon]

Is your speedo showing ONLY large kph numbers? Or is it showing large kph with small mph underneath?

 

[malfaour]

It shows mph as default I guess now. Everything else is Canadian. So progress?

If I check the box, it goes to km/h. Probably can’t change the wording. But I don’t care lol.

 

[malfaour]

Is your speedo showing ONLY large kph numbers? Or is it showing large kph with small mph underneath?

 

[malfaour]

I am now way too invested in seeing the outcome of this Canadian truck!

We will see if we can work the magic.

Ill be the test dummy lol.

Hopefully we can figure it out. Would be nice for everyone else. I have searched the forums and haven't seen anything successful that I know of.

 

[SilverPigeon]

Ok @malfaour Moe, do an IPC reboot in FORScan service procedures (wrench icon) for me please.

 

[SilverPigeon]

So @fordtruckman2003 and everyone, here's how DUSF works on the 12" cluster:
If set to imperial, speedo will default to mph, single display. When you go into steering wheel menu, there will be a setting to display speed in kph. This will enable dual display, top being a larger kph with smaller mph below the line.
If set to metric, the opposite behaviour happens. I like the dual speedo, because I'm a geek ? but if you want a single speedo with large numbers, uncheck that steering wheel menu setting.

On the smaller displays, the dual speedo may not be possible ?‍

 

[malfaour]

Done. Shows mph above the speed limit sign. Everything else is Canadian.

BTW HVAC is Celsius too not Fahrenheit.

 

[SilverPigeon]

@malfaour Moe, if the IPC reboot still has the odometer in kph, the only way I know of to set that right is in SYNC settings. The only time you should have to revisit that to change it is if an OTA hits the APIM or you reboot the APIM in FORScan service procedures.

 

[malfaour]

@malfaour Moe, if the IPC reboot still has the odometer in kph, the only way I know of to set that right is in SYNC settings. The only time you should have to revisit that to change it is if an OTA hits the APIM or you reboot the APIM in FORScan service procedures.

Ok. so the rest is Sync changes. That's fine.

 

[SilverPigeon]

Ok. so the rest is Sync changes. That's fine.

Yes Moe, but there maybe a way in asbuilt configuration; I think the default APIM behaviour is governed by country code. If you're willing, you can make this change to try it:

Change APIM 7D0-03-01 from 4341 xxxx xx-- (CA=Canada) to 5553 xxxx xx-- (US=United States). If that doesn't fix it, I can investigate further.

Sponsored