2021 F150 Advanced Security Pack

[DcnPat]

Where did you find the parts that were missing ? What are the part numbers? and these are the codes for foreskin to make it work?

Those are the FORscan codes I modified to get mine working. Were there is an * you need to check your truck's as built value against the spreadsheet and find the same options with the security pack also enabled.

The only part missing from my 23 Limited was the intrusion/inclination sensor. My sticker showed:

Advanced Security Pack Removal - 50.00

I ordered the sensor from a Ford parts dealer online for $35.
Part number on the parts bag: LC5Z-15K609-A
Part number on the sensor: LC5T-15K609-BA

Sponsored

 

[Buddy726]

Those are the FORscan codes I modified to get mine working. Were there is an * you need to check your truck's as built value against the spreadsheet and find the same options with the security pack also enabled.

The only part missing from my 23 Limited was the intrusion/inclination sensor. My sticker showed:

Advanced Security Pack Removal - 50.00

I ordered the sensor from a Ford parts dealer online for $35.
Part number on the parts bag: LC5Z-15K609-A
Part number on the sensor: LC5T-15K609-BA

Ok I’ll look. It should be the same on my 23 platinum I got back in January. And I also had Advanced Security Pack Removal - 50.00

 

[lb7047]

Those are the FORscan codes I modified to get mine working. Were there is an * you need to check your truck's as built value against the spreadsheet and find the same options with the security pack also enabled.

The only part missing from my 23 Limited was the intrusion/inclination sensor. My sticker showed:

Advanced Security Pack Removal - 50.00

I ordered the sensor from a Ford parts dealer online for $35.
Part number on the parts bag: LC5Z-15K609-A
Part number on the sensor: LC5T-15K609-BA

Got it working this morning. I found the Gen13 instructions and cross referenced the configuration by name since the addresses are different. I ended up verifying/modifying the following addresses:

IPC
720-02-02 *xxx xx-- make sure PARGCF is enabled (mine was)
720-09-02 xxxx *x-- enable PAGR
720-11-01 xxx* xxxx xx-- Perimeter Alarm Text (mine is set to motion sensors)

BCM
726-02-02 x1xx x1xx xx-- Set Retrig config to enabled and security config to both
726-55-01 xxxx xx01 xx-- LIN CSM Config
726-65-01 xxxx xxx1 xx-- CSM Slave present

APIM
7D0-09-01 xxxx xxx* xx-- Enable PARGCF
7D0-09-02 xxxx xxxx *x-- Enable PAGR

Then do the BCM LIN new module configuration process.

I found it much easier to install the sensors after removing the console, the console back and the switch circuit board from the console. There are clips and screws that hold the switch circuit board in. Be gentle with the clips. I've pointed out the clips on one side in this photo by the big blue arrows.

I'm not sure if it make a difference, but I made sure the sensors are in the same order I've seen in other photos with the green in the middle, the red on the passenger side and the orange on the driver's side.

Those are the FORscan codes I modified to get mine working. Were there is an * you need to check your truck's as built value against the spreadsheet and find the same options with the security pack also enabled.

The only part missing from my 23 Limited was the intrusion/inclination sensor. My sticker showed:

Advanced Security Pack Removal - 50.00

I ordered the sensor from a Ford parts dealer online for $35.
Part number on the parts bag: LC5Z-15K609-A
Part number on the sensor: LC5T-15K609-BA

Thanks brother, so I just need to order 2 parts? LC5Z-15K609-A and LC5T-15K609-BA
I found LC5Z-15K609-A at the dealer for $30. I couldn't find LC5T-15K609-BA at the dealer it says part not found, I did find it on eBay for $90, I attached photos.The two parts look identical if Im looking at it right

 

[DcnPat]

Thanks brother, so I just need to order 2 parts? LC5Z-15K609-A and LC5T-15K609-BA
I found LC5Z-15K609-A at the dealer for $30. I couldn't find LC5T-15K609-BA at the dealer it says part not found, I did find it on eBay for $90, I attached photos.The two parts look identical if Im looking at it right

You just need to order 1 part. Those 2 different part numbers are for the same physical part. The bag the part comes in has one number on it (the LC5Z number) and the actual module has the other number on it (the LC5T number).

 

[lb7047]

You just need to order 1 part. Those 2 different part numbers are for the same physical part. The bag the part comes in has one number on it (the LC5Z number) and the actual module has the other number on it (the LC5T number).

Thanks Patrick, Hopefully it will fit my 2023 Fort F150 Tremor, I belief it will though. Now to figure out how to install all this with Forscan. I have used For scan to make a few changes.How hard was it to pull the overhead console down?

 

[DcnPat]

As long as the wiring harness is there you should be golden. Once you make the changes to all the modules you need to go to the wrench icon on the left hand side of the Forscan window and do the BCM LIN new module config. The truck needs to be on level ground according to the dialog/message box for that. It only takes a few seconds and you won't notice anything except Forscan will say it is done.

The overhead console comes down fairly easily but it is rather thin plastic on the edges. I used a wide bladed trim tool and started on the drivers side of the console about a inch from the rear corner and worked it out a bit then switched to the passenger side.

 

[lb7047]

As long as the wiring harness is there you should be golden. Once you make the changes to all the modules you need to go to the wrench icon on the left hand side of the Forscan window and do the BCM LIN new module config. The truck needs to be on level ground according to the dialog/message box for that. It only takes a few seconds and you won't notice anything except Forscan will say it is done.

The overhead console comes down fairly easily but it is rather thin plastic on the edges. I used a wide bladed trim tool and started on the drivers side of the console about a inch from the rear corner and worked it out a bit then switched to the passenger side.

 

[lb7047]

I recieved my module yesterday, the console is pretty tight up there I haven't attempted yet. how do you turn the alarm off and on in the menu? Is there a flashing light saying it's armed?

Thanks

 

[DcnPat]

I recieved my module yesterday, the console is pretty tight up there I haven't attempted yet. how do you turn the alarm off and on in the menu? Is there a flashing light saying it's armed?

Thanks

When you make the changes in Forscan you will get an alarm menu on the sync screen that let's you turn on and off the motion sensor and enable or disable a prompt on the instrument panel when you turn off the engine.

 

[lb7047]

When you make the changes in Forscan you will get an alarm menu on the sync screen that let's you turn on and off the motion sensor and enable or disable a prompt on the instrument panel when you turn off the engine.

Thanks Patrick

On your forscan changes. what number goes where the asterisk is? I don't have an option where it says Pargcf or PAGR

IPC
720-02-02 *xxx xx-- make sure PARGCF is enabled (mine was)
720-09-02 xxxx *x-- enable PAGR
720-11-01 xxx* xxxx xx-- Perimeter Alarm Text (mine is set to motion sensors)

APIM
7D0-09-01 xxxx xxx* xx-- Enable PARGCF
7D0-09-02 xxxx xxxx *x-- Enable PAGR

 

[DcnPat]

Thanks Patrick

On your forscan changes. what number goes where the asterisk is? I don't have an option where it says Pargcf or PAGR

IPC
720-02-02 *xxx xx-- make sure PARGCF is enabled (mine was)
720-09-02 xxxx *x-- enable PAGR
720-11-01 xxx* xxxx xx-- Perimeter Alarm Text (mine is set to motion sensors)

APIM
7D0-09-01 xxxx xxx* xx-- Enable PARGCF
7D0-09-02 xxxx xxxx *x-- Enable PAGR

I didn't want to put a value there because I don't know what your truck has or doesn't have. I don't want to break your truck ?

If you look on the spreadsheet from @Livinitup you will find the address like 720-02-02 and all the various settings. Find what your current value is, note the options that your current value enables/disables then find the value with those same settings AND the PAGR OR PARGCF enabled.

 

[lb7047]

I didn't want to put a value there because I don't know what your truck has or doesn't have. I don't want to break your truck ?

If you look on the spreadsheet from @Livinitup you will find the address like 720-02-02 and all the various settings. Find what your current value is, note the options that your current value enables/disables then find the value with those same settings AND the PAGR OR PARGCF enabled.

I can understand that LOL.I appreciate all the help you have giving me so far.
I found the info I need but not sure which vss style to use to for IPC
720-11-01 xxx* xxxx xx perimeter alarm text

4 =	CEAM disabled • PAT Motion Sensors • VSS Style 1
5 =	CEAM disabled • PAT Motion Sensors • VSS Style 2
6 =	CEAM disabled • PAT Motion Sensors • VSS Style 3
7 =	CEAM disabled • PAT Motion Sensors • VSS Style 4

 

[DcnPat]

I can understand that LOL.I appreciate all the help you have giving me so far.
I found the info I need but not sure which vss style to use to for IPC
720-11-01 xxx* xxxx xx perimeter alarm text

4 =	CEAM disabled • PAT Motion Sensors • VSS Style 1
5 =	CEAM disabled • PAT Motion Sensors • VSS Style 2
6 =	CEAM disabled • PAT Motion Sensors • VSS Style 3
7 =	CEAM disabled • PAT Motion Sensors • VSS Style 4

I'm pretty sure mine was 4 from the factory (the value 4 not Style 4)

 

[lb7047]

I'm pretty sure mine was 4 from the factory (the value 4 not Style 4)

I have a 2023, ours should be close. Thanks brother

 

[HammaMan]

I was a bit surprised to find a blue box when I pulled the console down. Turns out it is a dummy blue box that is empty inside.

LOL -- Some of the stuff ford is pulling with deletes. Almost unbelievable.

Sponsored