ECU module programming guide using FDRS

[jeffm4688]

Yes this is correct.

Ok so I tried this and I am receiving the following error. I tried twice.

OTX Application
Procedure Unsuccesful - GetFilesForPMI

Exception getting flash part numbers

Sponsored

 

[Jesse-Infotainment]

Ok so I tried this and I am receiving the following error. I tried twice.

OTX Application
Procedure Unsuccesful - GetFilesForPMI

Exception getting flash part numbers

you selected no when asked if original module was installed

 

[jeffm4688]

you selected no when asked if original module was installed

I did based on other instruction.

Regardless of if I choose yes or no that same error pops up, the only difference is if I choose yes there is a requence where it says "turn off to install new module now" first.

 

[JoeBlowFord]

@Ajzride had the same issue I think.

https://www.f150gen14.com/forum/thr...ng-guide-using-fdrs.8249/page-153#post-187054

I believe he got around it by changing computers or uninstalling and re-installed FDRS.

https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-187578

IMPORTANT NOTE: If you go either route, make sure to "Return" the license in FDRS before doing anything.

 

[Ajzride]

@Ajzride had the same issue I think.

https://www.f150gen14.com/forum/thr...ng-guide-using-fdrs.8249/page-153#post-187054

I believe he got around it by changing computers or uninstalling and re-installed FDRS.

https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-187578

IMPORTANT NOTE: If you go either route, make sure to "Return" the license in FDRS before doing anything.

I resolved a different issue changing computers. The IPC not PMI was resolved when Jesse side loaded F188.

 

[Jesse-Infotainment]

I did based on other instruction.

Regardless of if I choose yes or no that same error pops up, the only difference is if I choose yes there is a requence where it says "turn off to install new module now" first.

Try to run a config and if that doesnt work it will have to be side loaded.

 

[jeffm4688]

Try to run a config and if that doesnt work it will have to be side loaded.

A config went through and completed without issue, although not sure how I would tell if I am good or not as I still can not PMI. I uninstalled FDRS, rebooted and set it up under a different user profile with no luck. Just for kicks I am going to use another laptop I have here which doesn't require me to use a usb-c to a adapter and give it a shot.

If this has to be side loaded, dare I ask whats involved?

 

[Jesse-Infotainment]

A config went through and completed without issue, although not sure how I would tell if I am good or not as I still can not PMI. I uninstalled FDRS, rebooted and set it up under a different user profile with no luck. Just for kicks I am going to use another laptop I have here which doesn't require me to use a usb-c to a adapter and give it a shot.

If this has to be side loaded, dare I ask whats involved?

I do everything remotely through teamviewer . Since it’s 188 it will only take 5mins to load the file.

I’ll look at your vin. Hopefully it loaded the 188 during the config. It doesn’t take long. You would know though because new updates would be available now.

 

[Jesse-Infotainment]

A config went through and completed without issue, although not sure how I would tell if I am good or not as I still can not PMI. I uninstalled FDRS, rebooted and set it up under a different user profile with no luck. Just for kicks I am going to use another laptop I have here which doesn't require me to use a usb-c to a adapter and give it a shot.

If this has to be side loaded, dare I ask whats involved?

Ok. We will need to side load it. You’ll need to install teamviewer.

 

[jeffm4688]

Ok. We will need to side load it. You’ll need to install teamviewer.

I have it already, do you want to PM me for code? I'll go back up to the truck & get ready if you wanna do it now.

 

[Jesse-Infotainment]

I’ll message you. Give me an hour or so.

 

[Paul Neubauer]

I am continually impressed by the way Jesse-infotainment goes above and beyond to help everyone with this stuff!

 

[Snakebitten]

He's the Ford OTA Czar

 

[JoeBlowFord]

He's the Ford OTA Czar

By now he has his own Ford botnet throughout the US. One of these days there will be an F150 automated pilgrimage to Dallas. ?

 

[Kanuck]

He's the Ford OTA Czar

HEAR THIS FORD...HIRE HIM...PAY HIM HUGE HUGE MONEY....

Sponsored