Adding Co-Pilot Assist 2.0 with Forscan?

[Jesse-Infotainment]

Yes. @superfordman has proven the ACC works with Rear cam only IPMA.

Sponsored

 

[Brandanr96]

Is the CCM the same for all engine models? I have a 5.0. But found my exact truck with the co pilot assist 2.0 VIN with a v6 would this work? @Jesse-Infotainment

 

[XLT22]

Yes they're all the same.

 

[ian0323]

With the amount of different builds on here I gotta be the guy to ask one more time.

2022 XLT 302A w/ 360 Cam, Max Trailer, Non-Nav, No front parking sensors

Looking to add ACC.

Basically I look for a truck with the stuff I want to add and order the parts I need from that VIN?
I have the 4 wires necessary behind the dash. That means I need to get a new bumper harness?
All the builds I have found of course have the connected nav. Will it screw up any of the part numbers since I don't have connected nav?

So I'll need CCM, Bumper harness, bracket for CCM and bolts, a crap load of Forscan changes.

I can post VIN if need be to get a little bit more help.

Thanks

 

[personalt]

With the amount of different builds on here I gotta be the guy to ask one more time.

2022 XLT 302A w/ 360 Cam, Max Trailer, Non-Nav, No front parking sensors

Looking to add ACC.

Basically I look for a truck with the stuff I want to add and order the parts I need from that VIN?
I have the 4 wires necessary behind the dash. That means I need to get a new bumper harness?
All the builds I have found of course have the connected nav. Will it screw up any of the part numbers since I don't have connected nav?

So I'll need CCM, Bumper harness, bracket for CCM and bolts, a crap load of Forscan changes.

I can post VIN if need be to get a little bit more help.

Thanks

You might want to check wiring at IPMA. My 302A was prewired from bumper to a connector in passenger kickplate but not from there to IPMA. Excuse the chicken scratch but the orange ones are for radar cruise. If my notes are right the correct orinitation is connector facing you and pin 11 should be a purple wire on top right. On mine I was bascially missing the T that is for the radar.


I then ran the wires behind the dash to get to the other connector. I first tried to save money and buy the pins from digikey but evenually found it easier to by the ford kit. I could install the pin connectors okay but if they were not perfect that didnt slide in to the connector very easily

 

[superfordman]

With the amount of different builds on here I gotta be the guy to ask one more time.

2022 XLT 302A w/ 360 Cam, Max Trailer, Non-Nav, No front parking sensors

Looking to add ACC.

Basically I look for a truck with the stuff I want to add and order the parts I need from that VIN?
I have the 4 wires necessary behind the dash. That means I need to get a new bumper harness?
All the builds I have found of course have the connected nav. Will it screw up any of the part numbers since I don't have connected nav?

So I'll need CCM, Bumper harness, bracket for CCM and bolts, a crap load of Forscan changes.

I can post VIN if need be to get a little bit more help.

Thanks

The front bumper harness should be all you need if you have the four wires at the IPMA connector.

Lack of nav will just mean IACC will not function, but everything else will just fine.

Yep, that's what you'll need.

 

[sdwndr]

I have a 2022 302a, December 2021 build. I have the 360 cameras too.

From what i can gather parts wise i need:
1. CCM: ML3Z-9E731-G
this is the complete assembly
2. wiring harness: ML3Z-15K867-MA
this is where i am a bit confused. when i look on the parts website, it says it is not compatible with MY 2022 trucks. what am i missing?
I have 360 camera, led headlight/fog light, and no front parking sensors. MY 22 f150
3. Associated bolts for mounting CCM
M6x20 or 25 flange bolts

I want to just add adaptive cruise, no front collision sensors. My wife has the ACC on her 2021 expedition and we love it. I do realize that IACC isn't possible and am ok with that. I also don't need the new steering wheel button as we keep it at 3 car lengths on her SUV and works great.

 

[superfordman]

I have a 2022 302a, December 2021 build. I have the 360 cameras too.

From what i can gather parts wise i need:
1. CCM: ML3Z-9E731-G
this is the complete assembly
2. wiring harness: ML3Z-15K867-MA
this is where i am a bit confused. when i look on the parts website, it says it is not compatible with MY 2022 trucks. what am i missing?
I have 360 camera, led headlight/fog light, and no front parking sensors. MY 22 f150
3. Associated bolts for mounting CCM
M6x20 or 25 flange bolts

I want to just add adaptive cruise, no front collision sensors. My wife has the ACC on her 2021 expedition and we love it. I do realize that IACC isn't possible and am ok with that. I also don't need the new steering wheel button as we keep it at 3 car lengths on her SUV and works great.

Yep, that is everything you need if its pre wired to the IPMA

 

[Plowman14]

@superfordman or @Jesse-Infotainment hoping one of you can help me out here with adding the lane centering and the adaptive cruise im getting lost/confusing myself with 45 pages on this topic lol. I have a 2023 XLT 2.7l 302A VIN 1FTEW1EP8PKD43721 with 360cam, trailer tow, nav, no front sensors, LED headlights and fogs. I did check the IPMA connector and I have all the necessary wires there there was a few posts about the connector on the passenger side not have the wires there. just want to make sure all I still need is the ML3z-9E731-G, ML3Z-15K867-MA and some bolts for mounting it. I am completely new to Fords and FORscan so would also like some help there via remote log in since that seems way deeper than my knowledge of vehicle computers lol

 

[superfordman]

@superfordman or @Jesse-Infotainment hoping one of you can help me out here with adding the lane centering and the adaptive cruise im getting lost/confusing myself with 45 pages on this topic lol. I have a 2023 XLT 2.7l 302A VIN 1FTEW1EP8PKD43721 with 360cam, trailer tow, nav, no front sensors, LED headlights and fogs. I did check the IPMA connector and I have all the necessary wires there there was a few posts about the connector on the passenger side not have the wires there. just want to make sure all I still need is the ML3z-9E731-G, ML3Z-15K867-MA and some bolts for mounting it. I am completely new to Fords and FORscan so would also like some help there via remote log in since that seems way deeper than my knowledge of vehicle computers lol

You are no different than @sdwndr right before you, so you need all the same parts and what you list is correct. Luckily you have nav so that should make everything work as intended. Where are you at in Nebraska?

 

[Plowman14]

You are no different than @sdwndr right before you, so you need all the same parts and what you list is correct. Luckily you have nav so that should make everything work as intended. Where are you at in Nebraska?

Awesome and just east of Grand Island

 

[Plowman14]

You are no different than @sdwndr right before you, so you need all the same parts and what you list is correct. Luckily you have nav so that should make everything work as intended. Where are you at in Nebraska?

Look what goodies showed up today. FORscan to OBD port deal should be here tomorrow

 

[Je1279]

Look what goodies showed up today. FORscan to OBD port deal should be here tomorrow

Jealous that yours has the wiring all the way to the bumper connector as my '23 302A does not. Definitely let us know how it goes!

 

[superfordman]

Awesome and just east of Grand Island

Good deal, I'm just south west of Ogallala so not exactly close but not far away either

 

[Plowman14]

@superfordman @Jesse-Infotainment well i attempted it today and got it all installed and talking but i kept failing the calibration so i dont know if its because i used a platinum to change perimeters or what i did wrong lol

Sponsored