Adaptive Head Lights - Coming to the US???

[brett_g]

Ok so total ForScan noob, but I went in yesterday for the first time and made some changes, pretty much this feature sparked me to actually do it.

I have the anti-glare selection in my screen, and my headlights do the "dance" left, right, up, down or whatever - they calibrate.

What I failed to comprehend was I still can turn on my "auto highbeams" the symbol with the green A in it. I seemed to have read that that should not be an option if they are actually turned on?

No idea on my build date, its a 402A tremor FWIW.

Sponsored

 

[ROBB1]

Ok so total ForScan noob, but I went in yesterday for the first time and made some changes, pretty much this feature sparked me to actually do it.

I have the anti-glare selection in my screen, and my headlights do the "dance" left, right, up, down or whatever - they calibrate.

What I failed to comprehend was I still can turn on my "auto highbeams" the symbol with the green A in it. I seemed to have read that that should not be an option if they are actually turned on?

No idea on my build date, its a 402A tremor FWIW.

Green indicator with A is what you want to see. That is glare free active. The normal auto high beams you had pre mod would have been a white indicator with A.

Edit to add: Welcome to the forscan club

 

[Sidwin]

Shoutout to: @tonesto7 and @Livnitup for paving the way.


Glare Free Menu (replaces Auto High beam) in APIM:
7D0-09-01 x1xx xxxx xx- -
7D0-09-03 xxCx xxxx xx- -
Note: a module reset in FORScan or power cycle is required for the menu to appear.

IPMA
706-01-01 xxxx xxx9 xx- -

SCCM
724-04-01 xxx4 xxxx - -

IPC
720-01-01 xx8x xxxx xx- -
720-10-01 xxxx xxx3 xx- -

HCM
734-01-01 xxxx xx01 xx- -
734-01-02 x3xx xxxx xx- -

Short bed No onboard scales / ccd
734-01-04 xx53 4E- -

Short bed with scales / ccd or Raptor
734-01-04 xx56 D1- -

Long bed no scales / ccd
734-01-04 xxD9 88- -

Long bed with scales / ccd
734-01-04 xxDC 17- -

worked for me
Thanks!
sid

 

[cheesedogf150]

Shoutout to: @tonesto7 and @Livnitup for paving the way.


Glare Free Menu (replaces Auto High beam) in APIM:
7D0-09-01 x1xx xxxx xx- -
7D0-09-03 xxCx xxxx xx- -
Note: a module reset in FORScan or power cycle is required for the menu to appear.

IPMA
706-01-01 xxxx xxx9 xx- -

SCCM
724-04-01 xxx4 xxxx - -

IPC
720-01-01 xx8x xxxx xx- -
720-10-01 xxxx xxx3 xx- -

HCM
734-01-01 xxxx xx01 xx- -
734-01-02 x3xx xxxx xx- -

Short bed No onboard scales / ccd
734-01-04 xx53 4E- -

Short bed with scales / ccd or Raptor
734-01-04 xx56 D1- -

Long bed no scales / ccd
734-01-04 xxD9 88- -

Long bed with scales / ccd
734-01-04 xxDC 17- -

Worked for me, thanks!

 

[Treich560]

Tried this on my headlight swapped xlt. No luck yet. Auto high beams are still in the menu. No option for glare free yet. Not sure it's possible?

 

[dolsen]

Tried this on my headlight swapped xlt. No luck yet. Auto high beams are still in the menu. No option for glare free yet. Not sure it's possible?

Did you install the HCM, or did you just do the headlight swap?

 

[Treich560]

Did you install the HCM, or did you just do the headlight swap?

It's the full harness. Auto levels on startup. HCM is installed.

 

[dolsen]

It's the full harness. Auto levels on startup. HCM is installed.

Gotcha, I don't have any input unfortunately, I am planning to do this swap by the end of the month and wanted to know what to look out for

 

[Treich560]

Gotcha, I don't have any input unfortunately, I am planning to do this swap by the end of the month and wanted to know what to look out for

The install was not that bad. Awesome to finally have high beams. I will go over the programming again. It was getting stuck at 100 percent when I reset the pcm.

 

[dolsen]

The install was not that bad. Awesome to finally have high beams. I will go over the programming again. It was getting stuck at 100 percent when I reset the pcm.

I was under the impression that you would need the ride height sensors for the auto leveling. Did you install those as well?

 

[Treich560]

I was under the impression that you would need the ride height sensors for the auto leveling. Did you install those as well?

I did not install the rear sensors.

 

[Treich560]

I was under the impression that you would need the ride height sensors for the auto leveling. Did you install those as well?

I have a video of them working. It would not let me post it though. File is to big.

 

[dolsen]

I did not install the rear sensors.

Are there front sensors? I thought there was but was unable to find anything about them, thought I did find the rears

 

[Treich560]

Are there front sensors? I thought there was but was unable to find anything about them, thought I did find the rears

I don't think so. Not sure it's necessarily auto leveling. Just goes through the calibration on start up. Like the upper trim levels do. It will stay at the height you have set. Projectors move left and right. Up and down.

 

[dolsen]

I don't think so. Not sure it's necessarily auto leveling. Just goes through the calibration on start up. Like the upper trim levels do. It will stay at the height you have set. Projectors move left and right. Up and down.

Auto leveling would be cool, but as long as I can get the dynamic bending and glare free, I'll be happy with that

Sponsored