ECU module programming guide using FDRS

[jfalat]

FDRS 40.4.5 is out.

Sponsored

 

[JayRay]

What Sync version is the truck on now? It is blank in PTS.

FDRS is showing an GWM update; not APIM. Did you get the one from earlier to go though?

I no longer have my FDRS license anymore, so I pulled this from FORscan instead.
APIM - Accessory Protocol Interface Module
Part number: MU5T-14G670-PNN
Calibration level: MU5T-14G670-PNN
Strategy : NU5T-14G676-EC
Calibration: MU5T-14G677-ABA

Last I saw, before midnight last night, was a new IPC update was showing, and after having done that through CAN a few days ago, I figured that was a good stopping point. I'll be aware of needing to do that, and who knows what other nested updates, when I pay another $50 later.

 

[rugedraw]

I no longer have my FDRS license anymore, so I pulled this from FORscan instead.
APIM - Accessory Protocol Interface Module
Part number: MU5T-14G670-PNN
Calibration level: MU5T-14G670-PNN
Strategy : NU5T-14G676-EC
Calibration: MU5T-14G677-ABA

Last I saw, before midnight last night, was a new IPC update was showing, and after having done that through CAN a few days ago, I figured that was a good stopping point. I'll be aware of needing to do that, and who knows what other nested updates, when I pay another $50 later.

Yes, certain modules need to be updated in sequence, so doing one update will cause another to pop up right after. This is true of APIM, GWM, TCU and IPC updates.

 

[Snakebitten]

FDRS 40.4.5 is out.

I couldn't successfully login with 40.4.5

Backed down to 40.4.1 and got in first attempt. Could just be anecdotal, but FYI

 

[JEB]

I couldn't successfully login with 40.4.5

Backed down to 40.4.1 and got in first attempt. Could just be anecdotal, but FYI

I had no problems logging in with 40.4.5, but I’m running Windows 10 Pro. Might be another Windows 11 problem.

 

[jfalat]

I had no problems logging in with 40.4.5, but I’m running Windows 10 Pro. Might be another Windows 11 problem.

same here.. no issues.. but also running windows 11.

 

[YACO]

This ACM update installs successfully (or at least it doesn't show any errors) but it comes back as if it didn't install. Any help would be greatly appreciated.

 

[Kanuck]

This ACM update installs successfully (or at least it doesn't show any errors) but it comes back as if it didn't install. Any help would be greatly appreciated.

I have had that update for about 2 years..installed many times and it still shows up..ignore it. Next time you get FDRS you can run. Not a big deal.

 

[rugedraw]

This ACM update installs successfully (or at least it doesn't show any errors) but it comes back as if it didn't install. Any help would be greatly appreciated.

Same thing on my truck and many others. You can ignore it if you already applied it.

 

[Snakebitten]

I would keep installing it until it goes away. ?

 

[Ajzride]

This ACM update installs successfully (or at least it doesn't show any errors) but it comes back as if it didn't install. Any help would be greatly appreciated.

while FDRS is updating F188 strategy (step7) quickly press up, up, down ,down, left, right, left, right, b,a,b,a followed by enter. This will allow the procedure to complete and properly remove it from your list.

 

[Kanuck]

I would keep installing it until it goes away. ?

I do and sometimes it install something. Not any noticeable improvement tho.

 

[Kanuck]

while FDRS is updating F188 strategy (step7) quickly press up, up, down ,down, left, right, left, right, b,a,b,a followed by enter. This will allow the procedure to complete and properly remove it from your list.

WHAT.??????????????????????? Are you pulling my chain?

 

[Mstephens20]

Hey guys just purchased 2 day license and first time trying to login to FDRS and I’m getting “User authentication failed”.
Using Windows 11.
Checked my credentials on the ford service site.
I’ve seen people having problems with the latest FDRS version 40.4.5 but can’t find where to download an earlier version.
any help would be much appreciated!!

 

[Ajzride]

Hey guys just purchased 2 day license and first time trying to login to FDRS and I’m getting “User authentication failed”.
Using Windows 11.
Checked my credentials on the ford service site.
I’ve seen people having problems with the latest FDRS version 40.4.5 but can’t find where to download an earlier version.
any help would be much appreciated!!

https://github.com/nitrobass24/FDRS-Archive/releases

Sponsored