Gotcha. My current values (changed) is showing: 7D0-02-02: 1202 00D8 00C7
yes correct once climate bar is put in the home button emerges
| Enable 75th Anniversary Splash Screen | APIM | 7D0-03-01 | xxxx | 24xx | xx-- | Requires Sync ver 22012 or higher - reset APIM in FORScan after either/both changes |
| Enable Unreal Sync Theme | APIM | 7D0-02-03 | xxxx | xxx1 | xx-- | |
| Enable Cimate Bar at the bottom of Sync screen | APIM | 7D0-02-02 | xxx* | xxxx | xx-- | use 2 for non-hybrid or 6 for hybrid - requires Unreal theme above |
| Enable Heated Steering Wheel on climate bar above | APIM | 7D0-02-01 | xxxx | *xxx | xx-- | see APIM spreadsheet for your value |
| Enable Cooled and/or Heated seats to climate bar above | APIM | 7D0-02-01 | xxxx | x*xx | xx-- | if you have heated & cooled seats then use A |
| Enable Lightning F150 Splash Screen | APIM | 7D0-03-01 | xxxx | 1Fxx | xx-- | |
| Enable Oil Life in Sync Settings, Vehicle | APIM | 7D0-10-01 | x8xx | xxxx | xx-- |
This didn’t work the way I intended it to be haha, I reverted the values for this back to stock until 3.5.3.yes correct once climate bar is put in the home button emerges
Enable 75th Anniversary Splash Screen APIM 7D0-03-01 xxxx 24xx xx-- Requires Sync ver 22012 or higher - reset APIM in FORScan after either/both changes Enable Unreal Sync Theme APIM 7D0-02-03 xxxx xxx1 xx-- Enable Cimate Bar at the bottom of Sync screen APIM 7D0-02-02 xxx* xxxx xx-- use 2 for non-hybrid or 6 for hybrid - requires Unreal theme above Enable Heated Steering Wheel on climate bar above APIM 7D0-02-01 xxxx *xxx xx-- see APIM spreadsheet for your value Enable Cooled and/or Heated seats to climate bar above APIM 7D0-02-01 xxxx x*xx xx-- if you have heated & cooled seats then use A Enable Lightning F150 Splash Screen APIM 7D0-03-01 xxxx 1Fxx xx-- Enable Oil Life in Sync Settings, Vehicle APIM 7D0-10-01 x8xx xxxx xx--
Checksums are calculated for each address block. Changing a bit changes the calc. "Yes" recalcs and writes the address with the correct checksum.I just got my 21 PB back from the dealer today to get the generator reset fixed. Ford engineers wanted the dealer to update all or a lot of the modules. I now have the CarPlay in full screen mode so I assume that's due to my Sync being upgraded, it was at 22192 and now it's at 22293.
I'm trying to see if I have Power-Up 3.5.3 but when I click on software Update Details all it says now if "your software is up to date." Before I took it into the dealer the Update Details said I had Power-Up 3.5.2. It seems odd it just says "it's up to date" now.
I tried to enable the 75th anniversary Splash Screen and Unreal Sync Theme but I get an error "incorrect checksum of data entered." I am entering 7D0-03-01 xxxx 24xx xx-- and 7D0-02-03 xxxx xxx1 xx--.
Would this be an indication I'm still at 3.5.2? I've attached the error message.
I just don't remember seeing that error message when I enabled Bambi mode.
yes if you do the apim reset, at least in my case its causes the modules to do a complete reboot and see all the new data. thats a very brief explanation
If you have full screen CarPlay, then you are at least at 3.5.3.
Ignore that, WRITE the values, then cycle the ignition as instructed. You may/will also need to reset the APIM module through FORScan after either and/or both the Unreal them and the 75th Anniversary spash screen edits.
After you WRITE your changes and cycle the ignition, if you need to reset a module, you can do it in FORScan. Note that you'll have to do it after applying changes for the Unreal theme and/or the 75th anniversary splash screen.
Yup, tons of people, including myself. That's what finally prompted me to bite the bullet, purchase what was needed, and do it myself.
yeah that makes sense. I do have Alexa, I saw it was active in Ford Pass and I logged into it today.
thanks again, I don't make changes with FORScan very often and when I do I watch the YouTube tutorials just to refresh. I did back up all the modules last yearAfter you WRITE your changes and cycle the ignition, if you need to reset a module, you can do it in FORScan. Note that you'll have to do it after applying changes for the Unreal theme and/or the 75th anniversary splash screen.
This, except choose APIM:
- Once connected, click the 'wrench' icon on the left.
- Make sure you're on the Service Procedures tab.
- Select the module (e.g., APIM).
- Click the blue circle with the arrow (start procedure)
- IIRC, you have to use the stop (circle /square) procedure icon when done here, too.
I also believe that the button sequence to reset the APIM module from the dash (hold the volume button and FF button simultaneously until the SYNC screen shuts down and the logo reappears, then let them go) accomplishes the same reset as the FORScan reset.
