Adding Co-Pilot Assist 2.0 with Forscan?

[Jesse-Infotainment]

1FTFW1E85PKF93320

Ill send you the gateway Update to get rid of the DTC

As far as the ACC not available you must have a change that is not meshing.

Did you already post the changes you made in the IPMA?

Sponsored

 

[jb22625]

Ill send you the gateway Update to get rid of the DTC

As far as the ACC not available you must have a change that is not meshing.

Did you already post the changes you made in the IPMA?

Thanks!

Adaptive cruise started working this morning with no further changes.

 

[Jesse-Infotainment]

Thanks!

Adaptive cruise started working this morning with no further changes.

Ok. GReat I have seen it require a sleep cycle to start working.

The update was sent

 

[jb22625]

Ok. GReat I have seen it require a sleep cycle to start working.

The update was sent

Performed the update and still getting the same error. Tried to reinstall from USB to make sure I did it properly and it said it was already installed. Could an error in setting up the forscan changes cause this?

 

[Jesse-Infotainment]

Performed the update and still getting the same error. Tried to reinstall from USB to make sure I did it properly and it said it was already installed. Could an error in setting up the forscan changes cause this?

It’s the corrupted software dtc right?

 

[Jesse-Infotainment]

Code: P1674 - Control Module Software Corrupted

Additional Fault Symptom 56):
- Invalid/Incompatible Configuration

Status (-0B):
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC

Module: Gateway Module A

Message me in the private convo I started instead of here with this so this thread doesn’t get derailed

 

[Jimboslice]

Alright! First and foremost thanks everyone in this thread especially Superfordman and Jesse-infotainment! I've received my ccm and wiring harness today. Took about 4 hours to install and change the forscan values. Works perfect! Acc, lane centering and speed sign recognition work as should and no long lasting DTC's. Here's a pic of my window sticker for the options I have. Thanks again!

 

[KTM753]

I have a 21' XL 101A Job 1 truck. I have Co-pilot360 2.0 but not Assist. I read early in the thread that an advanced IPMA isn't required.

But what about using a 4" cluster and 8" center screen? Will the ACC still work?

I am assuming that the IACC won't because there is no Nav data.

I know Jesse has done this on his XL but he also upgraded to 12" screen and full digital cluster.

Sorry to bump my reply again but curious about my question still. Will ACC work on my truck with 4" cluster screen and 8" center screen?

 

[Jimboslice]

Sorry to bump my reply again but curious about my question still. Will ACC work on my truck with 4" cluster screen and 8" center screen?

Yes, that's what I have and it works great.

 

[KTM753]

Yes, that's what I have and it works great.

Thanks for the direct response! What I wanted to hear!

 

[Jimboslice]

Here's a pic of my 4 inch productivity screen to show everyone what it looks like with acc and lane centering working.

 

[superfordman]

Alright! First and foremost thanks everyone in this thread especially Superfordman and Jesse-infotainment! I've received my ccm and wiring harness today. Took about 4 hours to install and change the forscan values. Works perfect! Acc, lane centering and speed sign recognition work as should and no long lasting DTC's. Here's a pic of my window sticker for the options I have. Thanks again!

Great to hear and glad you got it all working! Sorry I never got back with your message, I was gone on vacation for a while, then got home and my desktop computer conked out, so haven't been on here very much lately.

 

[Superbooty]

Ok so I got the ccm, bumper harness and steering wheel switch ordered all should be here next week… leads me to a preperation question. Did you guys change all forscan lines at one time after installing ccm or select ones before and others after? Any one disconnect batteries for install? I know i will to remove the airbags but for the harness or bumper removal?

 

[superfordman]

Ok so I got the ccm, bumper harness and steering wheel switch ordered all should be here next week… leads me to a preperation question. Did you guys change all forscan lines at one time after installing ccm or select ones before and others after? Any one disconnect batteries for install? I know i will to remove the airbags but for the harness or bumper removal?

Just go down the list one by one when making changes if you want just to be safe. It is a mix of easy mode changes and asbuilt changes so you'll be back and forth already.

 

[Superbooty]

Just go down the list one by one when making changes if you want just to be safe. It is a mix of easy mode changes and asbuilt changes so you'll be back and forth already.

What ones are the easy mode changes? All i see is a list of the asbuilt changes or am i miss interpreting the easy mode portion.

Sponsored