2021+ F-150 FORScan List / Database / Spreadsheet

[gspete]

So, I did the remote actuated windows up and down. It seems to only work on the front windows. Only the front windows have the Auto Up/Down. Does that make sense or did I miss something?

Sponsored

 

[FrankThompson]

So, I did the remote actuated windows up and down. It seems to only work on the front windows. Only the front windows have the Auto Up/Down. Does that make sense or did I miss something?

It is my understanding that is correct. Only the front windows will do this.

 

[AutonomousHybridF150]

i am not really going to watch it like a hawk until i get 1k miles on it
short trips are killing me, its almost 4 miles from my door (15-20 mph with four stop signs) to the main road that is 65 for 6 miles then another 12 at 60 to 70 my doc. so its really not getting worked out.

I have worked in many locations since ownership, and you really have to either: warm truck ICE by remote starting for 5-10 mins (which hits your gas tank MPG but not the trip meter) and then once your “this trip” begins it will Only show MPG earned since you pushed the Start button (OR) you must drive 12+ miles (depending on outside temp, until at normal operating temp) and then you should achieve 24 MPG after that. You just have to baby it until it is hot. Until the ICE is hot, the computer runs the engine super rich, causing lower MPG if you drive hard during the warm up process.

After 5000 miles, the drivetrain does loosen up allowing for better MPG. Until you have more miles, keep your tires at 38+ to compensate for the break in drag.

 

[Mike G]

I have worked in many locations since ownership, and you really have to either: warm truck ICE by remote starting for 5-10 mins (which hits your gas tank MPG but not the trip meter) and then once your “this trip” begins it will Only show MPG earned since you pushed the Start button (OR) you must drive 12+ miles (depending on outside temp, until at normal operating temp) and then you should achieve 24 MPG after that. You just have to baby it until it is hot. Until the ICE is hot, the computer runs the engine super rich, causing lower MPG if you drive hard during the warm up process.

After 5000 miles, the drivetrain does loosen up allowing for better MPG. Until you have more miles, keep your tires at 38+ to compensate for the break in drag.

I will be so glad when I trade mine in. 19mpg is not the 24mpg that’s on the Monroney.
Mike

 

[JDHRNC]

Not sure if anyone has been able to figure this out yet, but I did the coding change through FORScan to enable temperatures being shown on the instrument cluster for water and transmission temps. Is there a way to program oil temp into the cluster as well?

 

[Snakebitten]

Not sure if anyone has been able to figure this out yet, but I did the coding change through FORScan to enable temperatures being shown on the instrument cluster for water and transmission temps. Is there a way to program oil temp into the cluster as well?

I don't believe so. At least not on any of the turbocharged motors. Oil temps aren't even available as a PID from the ODB interface. Haven't been in more than a decade. More than mildly irritating to this old school engine monitoring geek.

Fortunately oil pressure IS a PID and its interesting to monitor the dual stage (variable) oil pump in the 3.5 Ecoboost motor.

 

[JDHRNC]

I don't believe so. At least not on any of the turbocharged motors. Oil temps aren't even available as a PID from the ODB interface. Haven't been in more than a decade. More than mildly irritating to this old school engine monitoring geek.

Fortunately oil pressure IS a PID and its interesting to monitor the dual stage (variable) oil pump in the 3.5 Ecoboost motor.

Thanks for the info. My Lariat is equipped with the 5.0L V8.

 

[crsavage1]

I changed the values for cameras at speed awhile ago and it worked. My truck updated last night and now cameras at speed do nothing. I did manage to get the Bed Camera screen in my 12 inch display but it does not bring up the picture. Just the screen with a button to push which should bring up the image but it just pauses and then acts like it hasn't been pushed. The update last night said it was the recall for trailer brake and had programmed the module to fix that....but apparently something else changed as cameras at speed with the values changed from the spreadsheet don't seem to work. I also got back in and verified the values were still correct. I am pretty good about saving the values that were original but cannot seem to find the note for that change. Anyone know what the original values are? Might go back and forth to see....2021 Platinum Job 1

 

[gspete]

Not sure if anyone has been able to figure this out yet, but I did the coding change through FORScan to enable temperatures being shown on the instrument cluster for water and transmission temps. Is there a way to program oil temp into the cluster as well?

From what I understand that will only work on the 12" full digital dash. I did try making the changes using ForScan using the "obvious choices" on the 8" "Analog Gauge dash" with no joy. It doesn't really look like there is enough room for the digital readout, we will see.

 

[powerboatr]

I don't believe so. At least not on any of the turbocharged motors. Oil temps aren't even available as a PID from the ODB interface. Haven't been in more than a decade. More than mildly irritating to this old school engine monitoring geek.

Fortunately oil pressure IS a PID and its interesting to monitor the dual stage (variable) oil pump in the 3.5 Ecoboost motor.

yup we can see it in forscan as a PID in the data logger or oscilloscope for oil pressure, but no temps
but on the dash its just a swing gauge with no reference numbers.
my 250 had a oil temp indication in the truck area of the display , but on the dash gauge area it only showed a swing gauge to indicate pressure.

i have the trans, and eng water showing temp numbers and the boost thing that just shows a swing, but no numbers, same as on the super duty

for me oil pressure and or temps would be awesome to see in the dash somewhere,

 

[antho]

yup we can see it in forscan as a PID in the data logger or oscilloscope for oil pressure, but no temps
but on the dash its just a swing gauge with no reference numbers.
my 250 had a oil temp indication in the truck area of the display , but on the dash gauge area it only showed a swing gauge to indicate pressure.

i have the trans, and eng water showing temp numbers and the boost thing that just shows a swing, but no numbers, same as on the super duty

for me oil pressure and or temps would be awesome to see in the dash somewhere,

I enabled oil temp but I can’t find any indication of getting the temp under the swing gauge like the other temp gauges. I have a raptor so I was able to add the oil temp in my measurements but would be nice to have it on both.

 

[ENG430]

I enabled oil temp but I can’t find any indication of getting the temp under the swing gauge like the other temp gauges. I have a raptor so I was able to add the oil temp in my measurements but would be nice to have it on both.

I am looking to install 2021 Raptor steering wheel on my Lariat 502a. If you could please have the Raptor steering wheel part number? Or only if you can give me your vin number and my dealer can order the exact part number. I really like the shifter paddle more than the buttons on the center gear. TIA

 

[antho]

I am looking to install 2021 Raptor steering wheel on my Lariat 502a. If you could please have the Raptor steering wheel part number? Or only if you can give me your vin number and my dealer can order the exact part number. I really like the shifter paddle more than the buttons on the center gear. TIA

@ENG430
I don’t have it on top of my head. You could pull any vin from a raptor on the ford website.

 

[AutonomousHybridF150]

I changed the values for cameras at speed awhile ago and it worked. My truck updated last night and now cameras at speed do nothing. I did manage to get the Bed Camera screen in my 12 inch display but it does not bring up the picture. Just the screen with a button to push which should bring up the image but it just pauses and then acts like it hasn't been pushed. The update last night said it was the recall for trailer brake and had programmed the module to fix that....but apparently something else changed as cameras at speed with the values changed from the spreadsheet don't seem to work. I also got back in and verified the values were still correct. I am pretty good about saving the values that were original but cannot seem to find the note for that change. Anyone know what the original values are? Might go back and forth to see....2021 Platinum Job 1

I had everything you mentioned enabled since 1.7.1, and after all updates to Bluecruise it allowed viewing the 3 cameras at speed. Buttons selected the views.

Maybe you need to allow a few engine cycles.

 

[crsavage1]

I had everything you mentioned enabled since 1.7.1, and after all updates to Bluecruise it allowed viewing the 3 cameras at speed. Buttons selected the views.

Maybe you need to allow a few engine cycles.

Thanks for the reply. Ironically, I towed the lift I had rented over the weekend back to the rental place this morning and it worked again. May have just been a fluke. You mention "buttons selected the views" I assume you mean the camera button and not a sidebar screen in the 12 inch display correct? Even though I have that option for the in bed camera, it does not work. Only the actual camera button brings up the views at speed.

Sponsored