Adding Adjustable Pedals?

[MikeMq1]

For XLT the adjustable pedals are prewired at the switch. To add memory adjustable pedals would be a HUGE job because the DSM handles all the memory functions. The switch panel needs to be replaced.

I added the full memory adjustable pedals. Let me also tell you.. TO remove the brake pedal bracket is a insane job. You may be able to remove the cluster to access the upper bolt but it was so insane I wound up jsut pulling the pedal and using the existing backet. Im not some doofus mechanically either. Its insane to get that bracket out. Thankfully the bracket is the same adjustable or not. You also need to replace the gas pedal and they are sold separately and the gas pedal is cable driven and there is some stupid way to make sure they are synced.

So the wiring is there on every XLT I have seen. You probably can get the whole assembly on ebay fairly inexpensive. You need the switch the panel and the brake and gas pedal.

There is no programming required.

What wiring harness would be needed for 2023 F150 xlt ? Or is the truck prewired?

Sponsored

 

[MikeMq1]

What wiring harness would be needed for 2023 F150 xlt ? Or is the truck prewired?

The plug for the switch was plugged into a blank next to the ebrake handle

 

[MikeMq1]

waking up dead post because now I want to attempt

Did you do the install? If so where did you tap into power and ground?

 

[MikeMq1]

What wiring harness would be needed for 2023 F150 xlt ? Or is the truck prewired?

I know I wear you out but, where is the plug for the motor located or do I have to run a pigtail to the BCM. The pedal I purchased has a 4 pin connector at the motor, I assume for the memory and power function, do you have a wire diagram that shows the pin configuration, I do not have memory seats.

 

[MikeMq1]

I know I wear you out but, where is the plug for the motor located or do I have to run a pigtail to the BCM. The pedal I purchased has a 4 pin connector at the motor, I assume for the memory and power function, do you have a wire diagram that shows the pin configuration, I do not have memory seats.

never mind, I'm an idiot, got the wrong one. I found the plug. Sorry to bather you...LOL

 

[Fonzy007]

The plug for the switch was plugged into a blank next to the ebrake handle

Mine wasnt there, but had a compustar alarm installed and i assumed the installer used the wires lol

 

[Griffalo]

Can this be done fairly easy on a 24 XLT? Anyone with part numbers available? Sounds like this would work for my truck and letting my girlfriend drive sometimes.

 

[Fonzy007]

Can this be done fairly easy on a 24 XLT? Anyone with part numbers available? Sounds like this would work for my truck and letting my girlfriend drive sometimes.

I purchased the pedal assembly, switch and panel from eBay all 3 for a little under $200 I see the plug sitting there for the gas pedal but my plug that I use for the switch.

I went on eBay and just searched electric gas and brake pedal for 23 ford f150 and it popped up

 

[TheDudeee]

Can this be done fairly easy on a 24 XLT? Anyone with part numbers available? Sounds like this would work for my truck and letting my girlfriend drive sometimes.

I have done this mod and it is…….time consuming because you will have to swap out the pedal and there are no dummy connector or power wire present after 24+. I will send you the dm.

 

[Griffalo]

I have done this mod and it is…….time consuming because you will have to swap out the pedal and there are no dummy connector or power wire present after 24+. I will send you the dm.

I got your DM and I appreciate the info. Not sure how soon I'll get to this upgrade. Health issues make it impossible for me to work on it right now.

 

[pruett365]

I have done this mod and it is…….time consuming because you will have to swap out the pedal and there are no dummy connector or power wire present after 24+. I will send you the dm.

Can you help me out as well? I have the pedals and switch but no harness for the throttle pedal, there is a harness for the switch.
‘24 XLT

 

[TheDudeee]

Can you help me out as well? I have the pedals and switch but no harness for the throttle pedal, there is a harness for the switch.
‘24 XLT

Going to send you the dm. You will need to add the power wire too since ford stopped halfway there.

Sponsored