2021+ F-150 FORScan List / Database / Spreadsheet

[superfordman]

Correct. The cancel button.

The error I am referring to is the same message that showed up on IPC.

I truly appreciate you and your efforts.

@farmtruckman look through my Add ACC guide below and make sure your changes match up just to try but looking quickly looks like there are three that don't. Especially the IPC IACC enable. Try these changes:

				Adaptive Steering Comfort Menu (ASCM) • MFD (MFD) • Intelligent Adaptive Cruise Control (IACC) • Adaptive Headlamps Feature (AHF)
720-09-02	*xxx	xx--		IACC enabled	to 2
				Dim II Control Mirror (DIICM) • TSR NCAP Adaptations (TSRNCAPA) • HDC Control Function (HDCCF) • Traffic Jam Assist (TJA)
720-10-01	x*xx	xxxx	xx--	TJA enabled	to B

				ModuleFeatureCfg_VideoOutput (MFCVO) • ModuleFeatureCfg_yrTAD (MFCTAD) • ModuleFeatureCfg_REMHarvest (MFCREMH) • ModuleFeatureCfg_REMLocalization (MFCREML)
706-01-01	xxxx	xxxx	x*--	MFCTAD Enabled • MFCREMH Enabled	8 to E

Sponsored

 

[SilverPigeon]

				Adaptive Steering Comfort Menu (ASCM) • MFD (MFD) • Intelligent Adaptive Cruise Control (IACC) • Adaptive Headlamps Feature (AHF)
720-09-02	*xxx	xx--		IACC enabled	to 2
				Dim II Control Mirror (DIICM) • TSR NCAP Adaptations (TSRNCAPA) • HDC Control Function (HDCCF) • Traffic Jam Assist (TJA)
720-10-01	x*xx	xxxx	xx--	TJA enabled	to B

Agree with 720-09-02, I made an error with 3 but just above I asked him to change it to 2.
720-10-01: disagree; you're turning on HDC where previously it was disabled

				ModuleFeatureCfg_VideoOutput (MFCVO) • ModuleFeatureCfg_yrTAD (MFCTAD) • ModuleFeatureCfg_REMHarvest (MFCREMH) • ModuleFeatureCfg_REMLocalization (MFCREML)
706-01-01	xxxx	xxxx	x*--	MFCTAD Enabled • MFCREMH Enabled	8 to E

Agree, I was looking one character to the left in my asbuilt so yes to "E"

 

[farmtruckman]

Agree with 720-09-02, I made an error with 3 but just above I asked him to change it to 2.
720-10-01: disagree; you're turning on HDC where previously it was disabled
Agree, I was looking one character to the left in my asbuilt so yes to "E"

@farmtruckman look through my Add ACC guide below and make sure your changes match up just to try but looking quickly looks like there are three that don't. Especially the IPC IACC enable. Try these changes:

				Adaptive Steering Comfort Menu (ASCM) • MFD (MFD) • Intelligent Adaptive Cruise Control (IACC) • Adaptive Headlamps Feature (AHF)
720-09-02	*xxx	xx--		IACC enabled	to 2
				Dim II Control Mirror (DIICM) • TSR NCAP Adaptations (TSRNCAPA) • HDC Control Function (HDCCF) • Traffic Jam Assist (TJA)
720-10-01	x*xx	xxxx	xx--	TJA enabled	to B

				ModuleFeatureCfg_VideoOutput (MFCVO) • ModuleFeatureCfg_yrTAD (MFCTAD) • ModuleFeatureCfg_REMHarvest (MFCREMH) • ModuleFeatureCfg_REMLocalization (MFCREML)
706-01-01	xxxx	xxxx	x*--	MFCTAD Enabled • MFCREMH Enabled	8 to E

Thank you @SilverPigeon and @superfordman for your inputs. I made the changes to 720-09-02 and 706-01-01 followed by rebooting IPMA, IPC and APIM in that order. Taking the truck for a quick spin now. Screenshots:

 

[farmtruckman]

@SilverPigeon @superfordman Alright back from my drive and the issue is still there. IACC picks up the first time but stops working when I cancel it (throws the yellow box warning that IACC won't be available, just like the earlier IPC photo that I shared) and starts working again if I reboot the APIM module with the buttons.

Also noticed that the DTC in IPMA keeps showing up that it lost communication with APIM.

@SilverPigeon here are my values for 706-16-01:

We are almost there and I appreciate you both helping out.

 

[SilverPigeon]

@farmtruckman , next change is to leave TSR enabled but disable ISA (which isn't available anyway). If this change makes no difference, leave it in place and we'll try the next one.
edit: helps if I put it in the comment ?

720-03-01

x4xx

xxxx

xx--

 

[farmtruckman]

@farmtruckman , next change is to leave TSR enabled but disable ISA (which isn't available anyway). If this change makes no difference, leave it in place and we'll try the next one.

@SilverPigeon at this point, I have disabled SSR inside of ACC settings but SSR works fine outside of CC. You meant disabling the SSR feature inside of ACC on the APIM? Right?

 

[SilverPigeon]

@SilverPigeon at this point, I have disabled SSR inside of ACC settings but SSR works fine outside of CC. You meant disabling the SSR feature inside of ACC on the APIM? Right?

Sorry, forgot the change and edited above to add it ?

 

[farmtruckman]

Sorry, forgot the change and edited above to add it ?

No problem - I made the change. Should I take the truck for a spin? The ISA is now disabled so should I keep the option inside of ACC disabled too?

 

[SilverPigeon]

@farmtruckman, we're not going to concern ourselves with the DTC because that's most likely generated when you reboot the APIM while the IPMA is using it (during ACC). When you're all fixed up, you can delete it or it will eventually disappear on its own.

 

[SilverPigeon]

Go for a spin. Re-enable SSR in adaptive cruise control.

 

[farmtruckman]

@farmtruckman, we're not going to concern ourselves with the DTC because that's most likely generated when you reboot the APIM while the IPMA is using it (during ACC). When you're all fixed up, you can delete it or it will eventually disappear on its own.

Yeah makes sense, seen a fair bit of these when I updated modules with FDRS.

Go for a spin. Re-enable SSR in adaptive cruise control.

Ok, circle back in a few minutes. BRB.

 

[farmtruckman]

@SilverPigeon no luck, same yellow warning on the IPC when the SSR inside of ACC is enabled. :/

 

[SilverPigeon]

@farmtruckman Ok, I know it's a hassle, but I'd like to put the truck into a known status. Reboot IPC, IPMA and APIM from FORScan then take another spin. If that doesn't work, and you have SSR working with it turned off in ACC settings such that the signs are read but ACC doesn't respond to speed sign changes, and you have no IPC warning messages, we will have to leave it there until next week when I can research more or if someone else can assist in the meantime.

 

[farmtruckman]

@farmtruckman Ok, I know it's a hassle, but I'd like to put the truck into a known status. Reboot IPC, IPMA and APIM from FORScan then take another spin. If that doesn't work, and you have SSR working with it turned off in ACC settings such that the signs are read but ACC doesn't respond to speed sign changes, and you have no IPC warning messages, we will have to leave it there until next week when I can research more or if someone else can assist in the meantime.

@SilverPigeon no problem mate, I will have them rebooted and will take the truck for a spin later this afternoon and update the thread. If I get the same results, I will keep the SSR disabled in ACC. There were no warnings/messages on IPC in my last few drives when SSR was disabled in ACC.

I can wait till we know better and if the forum members have any ideas, please feel free to chime in.

Thanks for your help @SilverPigeon - really appreciate it.

 

[superfordman]

@farmtruckman what are you APIM values right now? Sounds like the same issue I fought trying to add ACC/IACC way back in the day maybe.

Sponsored