2021+ F-150 FORScan List / Database / Spreadsheet

[crazywayne311]

Ok, another noob question.
why does it say my adaptive front lighting is disabled?

Sponsored

 

[XLT22]

Wonder if it actually shows the reading, or it can do 400W "dumb" as if it was the base inverter.

I'll double check when I get home, but I 've been looking at this recently to wire in a new one using the existing wiring (to put in a pure-sine). I was concerned about this specifically because it was tied in on the Gen13, but the Gen14 uses a different base inverter than those.

I really don't see why it won't work. Must be missing something somewhere in the spreadsheet.

 

[Kaboom]

Added the Hitch assist to my 2021 KR PB, It works! however it backs up really fast and is not centered, off by about 6-8 inches to the left. tried recalibrating the rear camera but still off. might also be the reason that my Pro trailer backup will not find stickers and does not work with the yaw sensor after bluecruise update.

 

[crazywayne311]

Can someone please help. Not sure the issue. Tried enabling cameras in motion and the front camera in motion.
IPMA 706-02-02 I got E07F-CE03-0041 and it’s not working.
As far as the APIM 7D1-01-01 I got A081-0802-FF03
Says FD if you don’t have trailer back up assist and FF if you do.

 

[JattilaB]

Auto-Relock Door Lock after 30 or 45 Seconds (not taking credit, just did a little tracking and testing. 2022 F-150) will relock doors after unlocking (if physically opening the doors opening it will not relock) use I found for this is I often step on my key fob, and doors get unlocked without knowing, with this it relocks in 30 seconds.

 

[charliecbp]

I am backing up all of the module as built and the SOBD module stops and I get a message saying that the service procedure has stopped, is this normal?

 

[JattilaB]

I am backing up all of the module as built and the SOBD module stops and I get a message saying that the service procedure has stopped, is this normal?

I had a similar issue, I did reset(DTC)on the modual and the issue went away

 

[charliecbp]

I tried, I get no error codes found, cycle the ignition and same problem, all other modules backed up ok

 

[GrandpaD]

Every once in a while I wish my brain were about 40 years younger.

I have successfully installed the unreal ...and was able to add the heated/cooled seats... BUT, my brain can't figure out which setting to use for the heated steering wheel on the screen.

I've a Platinum with all the bells but I'm pretty certain no rear climate .
I'm assuming I use "4" with this-
7D0-02-01 xxxx-4xxx-xx--.

If not, which number does this old man use?

Thanks.

 

[JIMFOUNTAIN]

Added the Hitch assist to my 2021 KR PB, It works! however it backs up really fast and is not centered, off by about 6-8 inches to the left. tried recalibrating the rear camera but still off. might also be the reason that my Pro trailer backup will not find stickers and does not work with the yaw sensor after bluecruise update.

I am seeing the same hitch assist failures. I have a Job 1 2021 so no sticker support until the updates in 2022. Yaw sensor was working fine after the update but I never found the stickers very dependable even after enabling. I will retest stickers when it warms up.

Odd that stickers and yaw sensor were working before for you.

 

[pavementends]

Tried twice to enable Oil Life in Sync -> Vehicle settings but didn't work and got an APIM DTC both times. Checked my work 100 times... changed the second digit to an '8' from a '0'. 2021 302A 3.5EB... what am I missing?

 

[antho]

Tried twice to enable Oil Life in Sync -> Vehicle settings but didn't work and got an APIM DTC both times. Checked my work 100 times... changed the second digit to an '8' from a '0'. 2021 302A 3.5EB... what am I missing?

Did you reset the APIM? What DTC are you getting?

 

[pavementends]

Did you reset the APIM? What DTC are you getting?

Reset the APIM by holding POWER and FORWARD SEEK buttons? Sorry that's the only way I know how. If that's what you mean, then YES, I did that. Still didn't show up under Vehicle settings.

I'll take a pic of the DTC, standby...

 

[JIMFOUNTAIN]

Every once in a while I wish my brain were about 40 years younger.

I have successfully installed the unreal ...and was able to add the heated/cooled seats... BUT, my brain can't figure out which setting to use for the heated steering wheel on the screen.

I've a Platinum with all the bells but I'm pretty certain no rear climate .
I'm assuming I use "4" with this-
7D0-02-01 xxxx-4xxx-xx--.

If not, which number does this old man use?

Thanks.

Heated Steering Wheel is the 1 bit in that byte. Turning it on adds 1 to the existing value.... so add 1 to whatever you currently have. And "A" becomes "B" etc.

 

[GrandpaD]

Heated Steering Wheel is the 1 bit in that byte. Turning it on adds 1 to the existing value.... so add 1 to whatever you currently have. And "A" becomes "B" etc.

Thanks.

Mine is currently set with a 4 so we'll up it to a 5 next time I hook up the laptop.

Thanks.

Sponsored