Rear Parking Aid and Camera View

[BobWadd]

Also, did you make Park aid switch changes in the IPC? Seems like that would be why you have that popup in the IPC.

I do not believe so. Could the updates in the APIM and IPMA triggered this. I have made changes to the IPC in the past but always restore a backup if there are any issues.

-----

Attached are the ABs as requested.

Also attached the module info. Just in case...

Sponsored

 

[antho]

Yeah there are some random changes that don't line up but not sure 100% on which one would effect the issues you are having.

I would start with 706-12-01 xxxx-x4xx-xx--

 

[BobWadd]

I would start with 706-12-01 xxxx-x4xx-xx--

Done. No change but no errors either.

 

[BobWadd]

Had time this morning to compare the as builts I downloaded from Ford when I purchased the truck to yesterdays pulled by FORScan. No differences found that should affect the Rear Park Aid system.

Had a chance to look at this again. Last time I did it manually, this time I uses As-Built Explorer and found some differences interesting to me.

There is a lot of data that changed, page after page. Is this typical of updates? Still learning this process.

I'll keep working on it...

I also noticed when comparing the IPMA (706) with Livnitup's FORScan - 2021-25 F150 spreadsheet things just don't appear to line-up. I usually use the 'IPMA - 706' tab. Data now appears to line up better with the 'IPMA (BC 1.4) - 706' tab. There is data that had '0000 0000 0000' previously and now has actual data in the fields. This was not like this previous to the FDRS updates.

'FORD CO-PILOT360 ASSIST 2.0' is what's listed on the window sticker.

 

[BobWadd]

I also noticed when comparing the IPMA (706) with Livnitup's FORScan - 2021-25 F150 spreadsheet things just don't appear to line-up. I usually use the 'IPMA - 706' tab. Data now appears to line up better with the 'IPMA (BC 1.4) - 706' tab. There is data that had '0000 0000 0000' previously and now has actual data in the fields. This was not like this previous to the FDRS updates.

Yes, I'm quoting myself on this one...

Is there a way I can confirm that I should be using the BC settings?

 

[rugedraw]

Yes, the newer IPMA software would line up with the BC 1.4 tab, but your truck does not have and is not configured for BC.

 

[BobWadd]

Yes, the newer IPMA software would line up with the BC 1.4 tab, but your truck does not have and is not configured for BC.

I understand that I do not have BC. There were a lot of changes made to the IPMA data pulled with FORScan during the updates with FDRS. I'm still trying to figure out what caused all these changes and if those changes could have affected my Rear Park Aid.

I've hit a roadblock and do not know how to proceed at this point.

 

[rugedraw]

I understand that I do not have BC. There were a lot of changes made to the IPMA data pulled with FORScan during the updates with FDRS. I'm still trying to figure out what caused all these changes and if those changes could have affected my Rear Park Aid.

I've hit a roadblock and do not know how to proceed at this point.

Maybe it is the way you worded you question. You asked if you should be using BC settings, and the answer to that is no.

Tbh, I am stumped as to what you issue is. At this point, I would just have flashed the entire ab file from a similar truck that has everything working onto yours to see what happens instead of going line-by-line trying to figure out what's off.

 

[BobWadd]

Maybe it is the way you worded you question. You asked if you should be using BC settings, and the answer to that is no.

Tbh, I am stumped as to what you issue is. At this point, I would just have flashed the entire ab file from a similar truck that has everything working onto yours to see what happens instead of going line-by-line trying to figure out what's off.

Thanks

I could use the AB I have from when I first purchased the truck. Unfortunately, there is a different number of blocks on the IPMA. I will start looking for what I need...

The difference in the IPMA data is just one additional block at the end. Could I create an AB and add a block at the end with 0000 0000 00xx value?

 

[rugedraw]

Maybe post in the FORScan thread to see if someone can get the IPMA abt file from their truck. It would need to have similar features to yours, the same size bed and the same type of mirrors. You'd have to change the VIN in the first four lines of block 19 to match yours. Just convert the file from abt to txt, change the the VIN to yours, convert the file back to abt and then flash it on your truck. Make a back-up of your current one in case you need to revert back to it.

The VIN is located here:

706-19-01 = xxxx xxxx xx--
706-19-02 = xxxx xxxx xx--
706-19-03 = xxxx xxxx xx--
706-19-04 = xxxx --

So whatever IPMA file you use, change whatever is there to whatever your truck shows there before you flash it.

Sponsored