OnX6 Light Bar Grille Mount

[2022F150GreyCO]

Let me know what info you want! My bracket allows for 2,3,5 pod setup or up to a 20” light.
It uses all factory bolts, you just loosen your bumper and slide it in!

Do you have any issues with airflow to intercooler with 4pod lights? I have a 3.5EB

Sponsored

 

[SpaceWhiteF150]

Do you have any issues with airflow to intercooler with 4pod lights? I have a 3.5EB

4 Baja designs xl sports, on a 2.7! Absolutely no airflow issues!

 

[2022F150GreyCO]

what do you charge for the bracket for this? I like it

 

[SpaceWhiteF150]

what do you charge for the bracket for this? I like it

Mounts are listed on Axismounts.com

 

[SteveAndTheCrigBoys]

I receive my bracket from @SpaceWhiteF150 a while back. Procrastinated my decision on which light setup to go with on it but I finally pulled the trigger and am installing now.

Should have some pics in the next few weeks!

 

[BryC]

I receive my bracket from @SpaceWhiteF150 a while back. Procrastinated my decision on which light setup to go with on it but I finally pulled the trigger and am installing now.

Should have some pics in the next few weeks!

Watching how you make out. Just ordered that bar for my 25, going with baja designs squadron.

 

[SteveAndTheCrigBoys]

Got everything done on Saturday. The mount from @SpaceWhiteF150 fit great, though I don't see how it can be installed on a 3.5 Ecoboost without removing the bumper. Bumper nuts were on so tight I needed access from the top with a breaker bar on the ratchet. Getting to the "inside" nut from below was practically impossible due to the intercooler.

Had to trim more plastic than anticipated too. No biggie, the bumper removal is pretty simple and everything went back together well. Helped with clean wire routing too.

Full Build List:

• Auxbeam AR800 switch panel kit w/ engine bay mount from @4x4TruckLEDs.com
• Swarfworks F150 overhead console switch panel mount
• Squadron S2 rear lights, flood w/ 25' 14 AWG duplex "harness"
• Squadron Pro Driving Combo on diode dynamics a-pillar mounts
• 10" OnX6 light bar driving combo on the Axis Mount bracket, Sherpa mounts for the horizontal mounting.
• Built Right Industries front license plate bracket relocation mount.

I can take some more / better pics, let me know if anyone wants to see anything in particular or have any questions on the setup.

I'll probably add the BD fog light kit next year now that I know how easy bumper removal is. Only have 3/8 switches taken, really want to make that 4/8 haha.

 

[SpaceWhiteF150]

Got everything done on Saturday. The mount from @SpaceWhiteF150 fit great, though I don't see how it can be installed on a 3.5 Ecoboost without removing the bumper. Bumper nuts were on so tight I needed access from the top with a breaker bar on the ratchet. Getting to the "inside" nut from below was practically impossible due to the intercooler.

Had to trim more plastic than anticipated too. No biggie, the bumper removal is pretty simple and everything went back together well. Helped with clean wire routing too.

Full Build List:

• Auxbeam AR800 switch panel kit w/ engine bay mount from @4x4TruckLEDs.com
• Swarfworks F150 overhead console switch panel mount
• Squadron S2 rear lights, flood w/ 25' 14 AWG duplex "harness"
• Squadron Pro Driving Combo on diode dynamics a-pillar mounts
• 10" OnX6 light bar driving combo on the Axis Mount bracket
• .Built Right Industries front license plate bracket relocation mount.

I can take some more / better pics, let me know if anyone wants to see anything in particular or have any questions on the setup.

I'll probably add the BD fog light kit next year now that I know how easy bumper removal is. Only have 3/8 switches taken, really want to make that 4/8 haha.

Install turned out killer!!

 

[BryC]

Got everything done on Saturday. The mount from @SpaceWhiteF150 fit great, though I don't see how it can be installed on a 3.5 Ecoboost without removing the bumper. Bumper nuts were on so tight I needed access from the top with a breaker bar on the ratchet. Getting to the "inside" nut from below was practically impossible due to the intercooler.

Had to trim more plastic than anticipated too. No biggie, the bumper removal is pretty simple and everything went back together well. Helped with clean wire routing too.

Full Build List:

• Auxbeam AR800 switch panel kit w/ engine bay mount from @4x4TruckLEDs.com
• Swarfworks F150 overhead console switch panel mount
• Squadron S2 rear lights, flood w/ 25' 14 AWG duplex "harness"
• Squadron Pro Driving Combo on diode dynamics a-pillar mounts
• 10" OnX6 light bar driving combo on the Axis Mount bracket, Sherpa mounts for the horizontal mounting.
• Built Right Industries front license plate bracket relocation mount.

I can take some more / better pics, let me know if anyone wants to see anything in particular or have any questions on the setup.

I'll probably add the BD fog light kit next year now that I know how easy bumper removal is. Only have 3/8 switches taken, really want to make that 4/8 haha.

Which fuse did you tap for the Auxbeam panel? Do you have any daylight pics? Interested in your ditch light mounts.
Nice job!

 

[SteveAndTheCrigBoys]

Which fuse did you tap for the Auxbeam panel? Do you have any daylight pics? Interested in your ditch light mounts.
Nice job!

Fuse #19. Snowplow / Rear Heated Seats (of which I have neither). Ignition only powered. Working great!

Here are some more photos.

 

[SteveAndTheCrigBoys]

Which fuse did you tap for the Auxbeam panel? Do you have any daylight pics? Interested in your ditch light mounts.
Nice job!

Oh yeah, and the ditch light mounts are Diode Dynamics. Nothing particularly special about them. Easiest part of the setup for sure.

 

[4x4TruckLEDs.com]

Which fuse did you tap for the Auxbeam panel? Do you have any daylight pics? Interested in your ditch light mounts.
Nice job!

Ditch Kit: https://www.4x4truckleds.com/diode-dynamics-a-pillar-light-kit-for-2021-ford-f-150-w-sdhq-brackets/

Switch Panel Kit w/Mount + Overhead Console Mount: https://www.4x4truckleds.com/kr-off...ket-for-2015-ford-f-150-2017-ford-super-duty/

 

[BryC]

Used the axis bar and the bracket from 4x4truckleds.

 

[SteveAndTheCrigBoys]

Used the axis bar and the bracket from 4x4truckleds.

Ooh, great mounting idea for the breaker. I might copy that.

 

[SpaceWhiteF150]

Used the axis bar and the bracket from 4x4truckleds.

This is beautiful!!

Sponsored