3D Printed Tweeter Mount

[sceroguitars]

God BLESS YOU for making this! I was about to try and make my own, for my '25 non-B&O and my Audiofrog GS10's.

So they ended up fitting pretty well?

Sponsored

 

[sceroguitars]

Thanks for sharing this. Just what I was looking for!

Any chance you could give some guidance on how you installed the crossover blocks? I have the kicker cs and have not installed the tweeters yet because I'm not sure the best route for wiring these in with the crossovers.

Are you looking for HOW to wire in

I wanted to test this out, so I ordered both ML3Z-1503598-CA and ML3Z-1503599-CA. It has the more directed tweeter, I held it up while in the car and I'm not sure I noticed a color difference. I did pull mine out to see and only then could I really see a difference.

It also gave me an opportunity to get a picture of the tweeter mounted.

Is absolutely crazy the PRICE DIFFERENCE between these two...One is like $115, and the other is $435! Hilarious. Was gonna order some, until I saw that...

 

[nickn066]

Thanks for sharing this. Just what I was looking for!

Any chance you could give some guidance on how you installed the crossover blocks? I have the kicker cs and have not installed the tweeters yet because I'm not sure the best route for wiring these in with the crossovers.

I have the "crossover blocks" mounted on a behind the seat rack from MTI, then run wires through the door foot area thresholds up to the front on each side, into the tweeters.

 

[nickn066]

Are you looking for HOW to wire in


Is absolutely crazy the PRICE DIFFERENCE between these two...One is like $115, and the other is $435! Hilarious. Was gonna order some, until I saw that...

I'm not sure why the price is so high right now.

 

[bray1720]

I have the "crossover blocks" mounted on a behind the seat rack from MTI, then run wires through the door foot area thresholds up to the front on each side, into the tweeters.

Okay, so you're fully amped? How did you snake the wire for the door speaker?

I'm looking for wiring recommendations to just tap into the stock wiring and simplify the connections for the door speaker and tweeter from the crossovers.

Thanks.

 

[bray1720]

Are you looking for HOW to wire in


Is absolutely crazy the PRICE DIFFERENCE between these two...One is like $115, and the other is $435! Hilarious. Was gonna order some, until I saw that...

Yes, recommendations for wiring them in. Ideally without having to run a new wire through the body to door boot.

Thanks.

 

[nickn066]

Okay, so you're fully amped? How did you snake the wire for the door speaker?

I'm looking for wiring recommendations to just tap into the stock wiring and simplify the connections for the door speaker and tweeter from the crossovers.

Thanks.

I pulled up the trim panels and ran the wires, I didn't want to mess with any factory wiring

 

[bray1720]

I pulled up the trim panels and ran the wires, I didn't want to mess with any factory wiring

How did you connect to the door speakers?

 

[nickn066]

How did you connect to the door speakers?

Factory wiring, using this harness.

https://www.amazon.com/PAC-T-Harness-2018-2022-Non-Amplified-Connector/dp/B0C4VBMPTK/

 

[Warden95]

These are great. I just printed one up and unfortunately the mounting diameter is a little small for my tweeters. I’m new to 3d printing. How would I make the mounting hole a little larger but keep everything else the same? The tweeter angle is exactly what I was looking for

 

[sceroguitars]

These are great. I just printed one up and unfortunately the mounting diameter is a little small for my tweeters. I’m new to 3d printing. How would I make the mounting hole a little larger but keep everything else the same? The tweeter angle is exactly what I was looking for

If you tell me the model of tweeter you have, I could adjust the diameter of the inner hole, to fit yours.

I already did this last night to make it fit my AudioFrog Tweeters.

 

[Warden95]

If you tell me the model of tweeter you have, I could adjust the diameter of the inner hole, to fit yours.

I already did this last night to make it fit my AudioFrog Tweeters.

That would be awesome! I really appreciate it! I have the arc audio RS 1.0. Maximum outer diameter without ring is 1.907” with a cut out diameter of 1.613”. Here is a pic

 

[bray1720]

Factory wiring, using this harness.

https://www.amazon.com/PAC-T-Harness-2018-2022-Non-Amplified-Connector/dp/B0C4VBMPTK/

Thank you. Also printed the brackets. These are great!

Sponsored