2021+ F-150 FORScan List / Database / Spreadsheet

[Caneman88]

Does anyone know if there is a way to get a better resolution on BedCam since updated to 2.5.1.
got cameras without ForScan but the res is not as good as before with Forscan.
still don't have BlueCruise but seems close.

also lost this view. this pic is before using Forscan
I was waiting for BC to kick in before using Forscan to mess with cams again.
thanks in advance

Sponsored

 

[Billy231]

Hello, is there anyone within the NY or tri-state area who can help with some Forscan work for me?
I am new to all this, do not have the correct equipment and the local dealers that I have dealt with have no idea about any of these options that can be changed. Mainly DTE (fuel tank), Guage reading etc.
I travel, so can meet up if possible, let me know where you are located. Thanks...

 

[daemonic3]

Does anyone know if there is a way to get a better resolution on BedCam since updated to 2.5.1.
got cameras without ForScan but the res is not as good as before with Forscan.
still don't have BlueCruise but seems close.

also lost this view. this pic is before using Forscan
I was waiting for BC to kick in before using Forscan to mess with cams again.
thanks in advance

I loved that view! The big bed view and tiny 360 view simultaneously. I also noticed it was gone, now we only have full screen bed view. I did not pay enough attention to the resolution to notice it is lower quality though.

 

[daemonic3]

Sometime during a series of SW updates, not sure exactly which update, I lost Heated Steering and Heated/ Cooled seats functions. The rear heated seat buttons work, they are located on the center console facing the rear seats. The 5 On/Off buttons controlling the Heated Steering wheel and driver /passenger heated-cooled seats do not work. They are side by side and located on the dash underneath HVAC controls. The fact that I lost steering wheel and seat functions at the same time, and the buttons are side by side on the same row, make me think its a single problem.
Using FORScan I have changed AB 720-05-02-5xxx-xx__ to 720-05-02-0xxx-xx__ and then back to AB in an attempt to wake things up. This had no affect. There is a DSC in the IPC
Code: U2100 - Initial Configuration Not Complete
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
Could this DTC be the issue? I have not been able to clear this DTC using FORScan. Any suggestions would be greatly appreciated.

Did you (or anyone?) get a resolution on this? I also noticed (now that I'm caught up to 2.5.3) that I have lost the auto heat/cool seats. I can push the buttons and select auto heat/cool, but they do not turn on as I either crank up or down the temperature setting. At least a few versions back this was all working ever since I made the forscan mods.

Before I go mucking around hooking my work PC back up to my truck, I just wanted to see if others confirm this happened and if anyone solved it.

thanks!

 

[Caneman88]

2.5.3. was a APIM update may have lost some of your Forscan changes I just got 2.5.3. today I will see if I lost any of your settings

 

[daemonic3]

Did you (or anyone?) get a resolution on this? I also noticed (now that I'm caught up to 2.5.3) that I have lost the auto heat/cool seats. I can push the buttons and select auto heat/cool, but they do not turn on as I either crank up or down the temperature setting. At least a few versions back this was all working ever since I made the forscan mods.

Before I go mucking around hooking my work PC back up to my truck, I just wanted to see if others confirm this happened and if anyone solved it.

thanks!

Just to update on this: It was a false alarm. I was in my truck that day and cranked the thermostat knob all the way down, and then up to 80, and the seat never triggered to cool or heat even though the auto setting was on.

However, I have not been able to reproduce this. It is coming on as needed and expected every time since.

 

[jesdamian]

Tried adding cameras at speed to my Job 1 (April 21 build date) and its not working. After powering down and restarting to test, I shut off the truck and went into forscan and confirmed all the edits were done and in the system. As soon as I get past 6mph the cameras shut off. If I try to push the camera button a message says "for safety reasons... "

edit: Sync4 rev 244
Software version 21281_Product

Any thoughts?

 

[Caneman88]

reset your APIM module in FORscan

 

[STJonesin4]

I guess the instructions are just worded a little oddly, I will give it another shot!



Then unplug it I shall. Thanks for the clarification.

I read it the same way that you did. I have the "4" and couldn't figure out why I still had the beep.....

 

[Zhilyard]

Hi guys, can anyone who's decent with forscan verify what setting in the speaker 4/subwoofer/center that I should use to get a line level output from the subwoofer, (coming from b&o unleashed) hooked up a sub, and realized that the sound keeps getting diminished while driving.

Thanks

 

[Caneman88]

anyone know how to get rid of the banner ? please help thanks in advance

 

[ENG430]

Hi

any idea how to make air circulation not switching off while driving?
I noticed that some time the air circulation switch off and the fan increased for a time specially while driving on the highway.

 

[Ajzride]

Hi

any idea how to make air circulation not switching off while driving?
I noticed that some time the air circulation switch off and the fan increased for a time specially while driving on the highway.

There has been a whole thread dedicated to this, no one has solved it to my knowledge. Another case of our devices deciding they are smarter than us and not letting us do what we know we want to do.

 

[Itsjustmd]

anyone know how to get rid of the banner ? please help thanks in advance

I'm looking for that answer as well. Did you find anything out?

 

[Caneman88]

still looking for a solution

Sponsored