I don't know the year, one of the service / shop diagrams found on the site.
TRM Fuses. BCMC F91 C1035B p15 -- C1590 p15 -- C2498F p14 -> TRM.
F91 powers the unit - this is what creates the Left Signal, Right Signal, and Parking Lights
F107 feed goes to an internal relay and out on the Orange...
My guess is remove the corner nut, then one fuse strip lays on the the other and clips hold them on.
Maybe like an older one: BJB fuse box and mega fuses!
Bottom:
Post #16,327
"You have to be logged in to your Motorcraftservice.com acct on the computer in a separate window as you try logging in to FDRS.
Also you have to have pre purchased the subscription on the above website too before FDRS login."
Looked at my E-Torx sockets, they're countersunk like pictured.
Ford seems to use Torx Plus lately, so another tool for me: Lisle 83100 External Torx Plus® Socket Set.
I put 256GB Samsung Pro Endurance in my 3 Viofo dash cams that have Front, Rear recording to the uSD.
My Viofo A139 PRO manual says:
• The microSD card is sold separately. The microSD card must be High Endurance
type, have a UHS-U1/U3 or above rating and the capacity up to 256GB.
10 minute...
OBDII adapter and an app to see what the truck shows for voltage and amps.
The battery monitors like Quicklynks BM2 don’t measure amps.
I use the Quicklynks BM2 and Multi-Batt Mon app to watch voltages.
Power Point Relay inside BJB feeds the fuses for 12V outlets.
Battery Load Shedding (from couple different Ford manuals)
Vehicles built before 2025 have a partial load shed strategy.
Vehicles built after 2025 contain the full load shed strategy.
The BCM is the primary module that is...
Ford's 400W inverter info, troubleshooting, possible problems:
Both Inverter fuses OK.
Inverter to Outlet harness connections.
LEDs gone bad in the outlets so no feedback signal sent back to the BCM.
Pro Power is off, No onboard button, Not in features
No 110v AC and LEDs do not illuminate...
Exterior Lighting - System Operation and Component Description
The TRM supplies voltage to the trailer stop/turn lamps and trailer battery charging.
The TRM provides voltage to the trailer tow connector for trailer battery charging when all of the following are true:
• The TRM detects that a...
Might be the the truck has to detect a trailer is connected before it turns on 12v charge line.
Truck engine on, trailer connected, driver door closed, brake pedal press, put in gear for a few seconds(drive or reverse).
Guess I can't remember if I've changed Forscan "Connection Type", when switching between the OBDLink EX via USB for making changes with Forscan.
And the OBDLink MX+ for monitoring. Usually use MX+ with my phone.
I open Forscan & it seems to work with either adapter without changing anything...
Been a few years since I installed.
I probably followed the OBDLink Windows Quick Start Guide thru Pairing the OBDLink MX+
I don't use OBDWiz.
Verified in Windows 10 Device Manager my Bluetooth and Com Ports.
Looked at Forscan > Settings > Connection.
Windows 10
Win10 supplied the driver for...
The pinpoint tests for another Ford 400W inverter so Fuse #s are different:
A1 CHECK THE POWER OUTLET LED (LIGHT EMITTING DIODE) STATUS
• Start the vehicle (Ready indicator light ON).
• Check the LED on the AC outlet.
Did the LED illuminate?
Yes.
If the LED is on continuously, the direct...
General info on Ford's 400W Inverters.
A DTC sets in the BCM when the general electrical fault is detected by the direct current/alternating current (DC/AC) inverter.
Possible Causes
• Fuse(s)
• Direct current/alternating current (DC/AC) inverter
• AC Outlet
• Wiring, terminals or connectors...