No-drill Mud Flaps - recommendations?

[JJSnell]

I didn't even know clip-on was an option. Sounds like I'm going shopping at the local Home Depot parking lot this weekend. "Gone in 60 Seconds" has a whole new meaning and I will let you know what brand I get....

Sponsored

 

[CND Supercrew]

Damn I would need a loan to buy those!

Dealer installed on every truck before it hits the lot per DOT

 

[Aliass24]

I like the look of Rokblokz and ordered them for my '24. Turns out that they are not no drill on the 2024 model year. Maybe this has changed since then but probably best to confirm before going that route if you decide to do so. I ended up going with Weathertech. Easy install, look fine, and work for my driving needs.

I have the rokbloz’s on my 24” and there was no drilling involved, very easy install.

 

[daleric]

I have the Husky rear wheel well liners and would like to get the Husky rear mud flaps. Does anyone have both? Wondering if I need to remove the liners to install the flaps.

I have both and I did not have to remove the mud guards to put the liners in. Super easy install just pay attention to which liner goes on which side and you’ll be fine.

 

[mostater]

I have the rokbloz’s on my 24” and there was no drilling involved, very easy install.

I wished it worked out for me and that is why I suggested reaching out to Rokblokz first to verify. Here is part of the response I received from them when I inquired about the set I ordered...
"Unfortunately, we have found that many 2024 models do not have the hole at point 3 that earlier models do. As such we updated our instructions and hardware to reflect this difference. We do not have a no-drill option at this time."
I don't know... maybe a trim level thing??

 

[Aliass24]

I wished it worked out for me and that is why I suggested reaching out to Rokblokz first to verify. Here is part of the response I received from them when I inquired about the set I ordered...
"Unfortunately, we have found that many 2024 models do not have the hole at point 3 that earlier models do. As such we updated our instructions and hardware to reflect this difference. We do not have a no-drill option at this time."
I don't know... maybe a trim level thing??

There was one mounting point for the top of flap that I did have to add a screw and clip but the hole was already there but that’s it. My truck is a lariat although I think it wouldn’t matter.

 

[rxsamg]

I have the rokbloz’s on my 24” and there was no drilling involved, very easy install.

There was one mounting point for the top of flap that I did have to add a screw and clip but the hole was already there but that’s it. My truck is a lariat although I think it wouldn’t matter.

My '22 had Rokblokz installed by prev owner. I ordered a set of husky wheel well liners. I have a feelling I'll need to remove them and share one of the holes toward the rear of the well. I have to say I've had plenty of mudflaps over the years. The Rokblokz feel the most solid mounted.

 

[CarbonMark]

I have the rokbloz’s on my 24” and there was no drilling involved, very easy install.

What size tires do you have on your truck? Any rubbing on the mud flaps or anyplace else with your setup?

 

[FLPB]

Another vote for Husky. They were the shortest/lowest profile I could find, but still get the job done.

 

[Aliass24]

What size tires do you have on your truck? Any rubbing on the mud flaps or anyplace else with your setup?

I run 315/70/17 on 17x8.5 +25 methods. They only rub just barely on the drivers side hard reverse but not going forward. I have the caster maxed out as far as I could but still maintain a good camber spec. I also trimmed off that piece of plastic that they screw to the edge of the bottom fender for a bit more clearance. I wanted to run the 315’s so that little bit of rubbing is not worth the worry. The crash bars and everything else is good to go.

Sponsored