Search results

The side cameras are different from the front and back. They look the same but have a different part number. I'll look up the numbers. But if you are researching the part from the Ford shops the side cameras are significantly cheaper even new.

I'm out of the US for a couple weeks but I think I still have the PJ7Z camera. If I do, I can send it to you to see if it works. If so, I'll sell it to you, if not you can send it back.

Either FS or NA will work. Jesse corrected my statement about FS. If you don't source it from Jesse you should not PMI it to your truck. It will mess up the software.

In my case, I had to go through all of the changes and change them back until I found the conflict. The code will clear immediately or after a couple restarts (or module reset). I pulled your asbuilt but I don't think it had been changed yet. Sometimes it can be awhile or changes may never be...

I've done this before. Looking at the deltas and my Lariat configuration, I don't think it is BCM. In my case it was changes to the IPMA not matching the APIM. It is a process of getting the modules back in sync. What other module changes did you make? I would avoid updates or other changes...

Correction: OBD2 Port.

The IPMA needs to have the green connector on it next to the brown one. If you look up under the dash on the driver's side behind the ODBC port you can check if your IPMA has a green connector. It probably only has the brown one.

I did MCS in my 22 Lariat. I had to run power to both seats C311/312 pins 13 from C265 pin 35 and run CAN bus from Driver's seat (C311 pins 6&7) to passenger (C312 pins 4&5). You can tell at both seats by looking at the truck side of C311. Got this from @HammaMan diagrams in previous posts.

Look at my post #113 in this thread. That is all I've ever seen.

No, it only shows the rear camera no matter what is selected.

Was just eliminating possibilities. Between front and rear cameras, I tried multiple combinations, and it was pretty easy to identify bad combos. However, a key point I caught from your previous discussion - if there are any issues, it appears the ipma just gives up, and 360 won't work, no...

I have seen cases where coax has had issues (especially if it was damaged) but I did get all the runs tested. All of the cameras have displayed in port 2 as you identified. However, even though my right camera displays, I think it has a problem. @Jesse-Infotainment helped me get an update on...

Thanks @Tlusk7, I think people get confused on the bypass. @thunderf150 I think this would be the information you need. Let us know how you progress.

Sorry, didn't check these posts first. Depending on what is broken off, these are locks for the pins. If it is just the posts that hold the piece in place you may be able to reuse it as the connector together (latched) will hold the locking plate in place.

This was one of the toughest parts and why I was testing my coax. Did you watch @Tlusk7 s video? That was helpful. The other option is to bypass this connector altogether. You have to purchase the optional coax listed in his instructions plus the short gender changing coax as well, but then...

Still working on it. I was waiting for the "CBA" jumper between C316 and C1591. I have a duplicate set of coax and was tired of messing with my installed version. I have two extra ML3Z-19G490-BC cameras and one ML3Z-19G490-BB camera. When I did some initial testing the "BB" camera connected...

Thanks for the reference. That is the camera I have installed in the front. But I have a couple of duplicates. I am going to try bypassing the coax that I have run to see if it is a wiring issue.

Here is what I see when I push the camera button: Then if I select the Rear Option: Then if I go back to the 360 view option and select the magnifying glass: I have never seen any other displays with various Forscan settings. If I push the button again it goes back to the previous...

I am backing out most of my changes and will focus on the cameras. My thoughts may be a combination of the front and rear cameras since the rear has to change to show the hitch (mine doesn't). Right now the results are pretty binary: the "wrong" camera (250 or BEV or whatever it is associated...

No problem. Let me know if I can help with any of the questions.